Most magnetorheological (MR) fluid dampers are designed as fixed-pole valve mode devices, where the MR fluid is forced to flow through a magnetically active annular gap. This forced flow generates the damping force, which can be continuously regulated by controlling the strength of the applied magnetic field. Because the size of the annular gap is usually very small relative to the radii of the annulus, the flow of the MR fluid through this annulus is usually approximated by the flow of fluid through two infinitely wide parallel plates. This approximation, which is widely used in designing and modeling of MR dampers, is satisfactory for many engineering purposes. However, the model does not represent accurately the physical processes and, therefore, expressions that correctly describe the physical behavior are highly desirable. In this paper, a mathematical model based on the flow of MR fluids through an annular gap is developed. Central to the model is the solution for the flow of any fluid model with a yield stress (of which MR fluid is an example) through the annular gap inside the damper. The physical parameters of a MR damper designed and fabricated at the University of Manchester are used to evaluate the performance of the damper and to compare with the corresponding predictions of the parallel plate model. Simulation results incorporating the effects of fluid compressibility are presented, and it is shown that this model can describe the major characteristics of such a device—nonlinear, asymmetric, and hysteretic behaviors—successfully.
Skip Nav Destination
e-mail: s.o.oyadiji@manchester.ac.uk
Article navigation
December 2009
Research Papers
Mathematical Modeling, Analysis, and Design of Magnetorheological (MR) Dampers
Weng Wai Chooi,
Weng Wai Chooi
Dynamics and Aeroelasticity Research Group, School of Mechanical, Aerospace and Civil Engineering,
University of Manchester
, Manchester M60 1QD, UK
Search for other works by this author on:
S. Olutunde Oyadiji
S. Olutunde Oyadiji
Dynamics and Aeroelasticity Research Group, School of Mechanical, Aerospace and Civil Engineering,
e-mail: s.o.oyadiji@manchester.ac.uk
University of Manchester
, Manchester M60 1QD, UK
Search for other works by this author on:
Weng Wai Chooi
Dynamics and Aeroelasticity Research Group, School of Mechanical, Aerospace and Civil Engineering,
University of Manchester
, Manchester M60 1QD, UK
S. Olutunde Oyadiji
Dynamics and Aeroelasticity Research Group, School of Mechanical, Aerospace and Civil Engineering,
University of Manchester
, Manchester M60 1QD, UKe-mail: s.o.oyadiji@manchester.ac.uk
J. Vib. Acoust. Dec 2009, 131(6): 061002 (10 pages)
Published Online: October 27, 2009
Article history
Received:
January 12, 2008
Revised:
January 26, 2009
Published:
October 27, 2009
Citation
Chooi, W. W., and Oyadiji, S. O. (October 27, 2009). "Mathematical Modeling, Analysis, and Design of Magnetorheological (MR) Dampers." ASME. J. Vib. Acoust. December 2009; 131(6): 061002. https://doi.org/10.1115/1.3142884
Download citation file:
Get Email Alerts
Boundary-Element Analysis of the Noise Scattering for Urban Aerial Mobility Vehicles: Solver Development and Assessment
J. Vib. Acoust (October 2024)
Related Articles
Dynamic Spherical
Cavity Expansion in an Elastoplastic Compressible Mises
Solid
J. Appl. Mech (November,2005)
Electrorheological Dampers, Part II: Testing and Modeling
J. Appl. Mech (September,1996)
A New Approach to the Modeling of Magnetorheological Dampers and Application to Resonance Control
J. Fluids Eng (September,2021)
A Unified Approach for Flow Analysis of Magnetorheological Fluids
J. Appl. Mech (July,2011)
Related Proceedings Papers
Related Chapters
Damping of Cylindrical Structures in Single-Phase Fluids
Flow-Induced Vibration Handbook for Nuclear and Process Equipment
A New Low Cost Method For Measuring the Viscoelastic Behavior of Adhesives
Advances in Adhesives, Adhesion Science, and Testing
Characterization and Modeling of Viscoelastic Layer Damping Plate Based on Substructures
International Conference on Information Technology and Management Engineering (ITME 2011)