Abstract

Accurate prediction of lubrication characteristics, specifically film thickness and pressure distribution, is pivotal for ensuring optimal performance in ball screws. Despite its significance, there is a notable dearth of studies investigating the evolution of lubrication characteristics resulting from the changing surface roughness over prolonged operation of ball screws. Furthermore, obtaining the surface roughness of ball screws poses a challenge due to the limited loading capacity of measurement instruments. Traditional methods involving cutting the screw for surface roughness measurement are impractical for continuous monitoring during extended operation. To address this issue, the present study introduces an efficient approach to model the surface roughness of the raceway in double-nut ball screws. A profilometer is employed to measure profile roughness along two directions (parallel and perpendicular to the rolling direction) without the need to cut the screw raceway. The 2D power spectral densities and height probability densities of profile roughness are calculated to model the surface roughness, and the synthesized data are utilized to solve the Reynolds equation. The simulation method is validated through friction torque tests, demonstrating a calculation accuracy exceeding 92%. The study further explores the evolution of film thickness and pressure distribution in double-nut ball screws during running-in and steady wear stages, revealing severe asperity contact in the two nuts. Additionally, variations in load ratio, friction coefficient, and film thickness ratio (λ) are investigated. Considering the load ratio and λ of the slave nut, it can be inferred that boundary lubrication persists in the two nuts throughout the operation.

References

1.
Hu
,
J.
,
Wang
,
M.
, and
Zan
,
T.
,
2014
, “
The Kinematics of Ball-Screw Mechanisms via the Slide-Roll Ratio
,”
Mech. Mach. Theory
,
79
(
9
), pp.
158
172
.
2.
Xu
,
M.
,
Zhang
,
H.
,
Liu
,
Z.
,
Li
,
C.
,
Zhang
,
Y.
,
Mu
,
Y.
, and
Hou
,
C.
,
2021
, “
A Time-Dependent Dynamic Model for Ball Passage Vibration Analysis of Recirculation Ball Screw Mechanism
,”
Mech. Syst. Signal Process.
,
157
(
12
), p.
107632
.
3.
Qi
,
B.
,
Zhao
,
J.
,
Chen
,
C.
,
Song
,
X.
, and
Jiang
,
H.
,
2023
, “
Accuracy Decay Mechanism of Ball Screw in CNC Machine Tools for Mixed Sliding-Rolling Motion Under Non-Constant Operating Conditions
,”
Int. J. Adv. Manuf. Technol.
,
124
(
11–12
), pp.
4349
4363
.
4.
Cheng
,
Q.
,
Qi
,
B.
,
Liu
,
Z.
,
Zhang
,
C.
, and
Xue
,
D.
,
2019
, “
An Accuracy Degradation Analysis of Ball Screw Mechanism Considering Time-Varying Motion and Loading Working Conditions
,”
Mech. Mach. Theory
,
134
(
4
), pp.
1
23
.
5.
Cao
,
L.
,
Park
,
C. H.
, and
Chung
,
S. C.
,
2022
, “
Real-Time Thermal Error Prediction and Compensation of Ball Screw Feed Systems via Model Order Reduction and Hybrid Boundary Condition Update
,”
Precis. Eng.
,
77
(
5
), pp.
227
240
.
6.
Brecher
,
C.
,
Witt
,
S.
, and
Yagmur
,
T.
,
2009
, “
Influences of Oil Additives on the Wear Behavior of Ball Screws
,”
Prod. Eng.
,
3
(
3
), pp.
323
327
.
7.
Horng
,
J. H.
,
Chern
,
S. Y.
,
Wei
,
C. C.
,
Chang
,
Y. P.
, and
Wu
,
C. J.
,
2010
, “
Experimental Simulation of Tribological Study for the Mechanism in a High Speed-Heavy Load Ball Screw
,”
World Congress Eng.
,
2010
(
2
), pp.
1034
1040
.
8.
Fleischer
,
J.
,
Spohrer
,
A.
,
Leberle
,
U.
, and
Dosch
,
S.
,
2015
, “
Adaptive and Adequate Lubrication for Highest Component-Lifetimes in Feed Drive Axes With Ball Screws
,”
Proc. CIRP
,
29
(
4
), pp.
335
340
.
9.
Hamrock
,
B. J.
, and
Dowson
,
D.
,
1976
, “
Isothermal Elastohydrodynamic Lubrication of Point Contacts: Part 1—Theoretical Formulation
,”
ASME J. Lubr. Technol.
,
98
(
2
), pp.
223
228
.
10.
Wei
,
C. C.
,
Lin
,
J. F.
, and
Horng
,
J. H.
,
2009
, “
Analysis of a Ball Screw With a Preload and Lubrication
,”
Tribol. Int.
,
42
(
11–12
), pp.
1816
1831
.
11.
Oh
,
K.-J.
,
Cao
,
L.
, and
Chung
,
S.-C.
,
2020
, “
Explicit Modeling and Investigation of Friction Torques in Double-Nut Ball Screws for the Precision Design of Ball Screw Feed Drives
,”
Tribol. Int.
,
141
(
1
), p.
105841
.
12.
Cao
,
L.
,
Oh
,
K.-J.
, and
Chung
,
S.-C.
,
2020
, “
Explicit Precision Friction Torque Model of Ball Screws in High Speed Operations
,”
Tribol. Int.
,
152
(
12
), p.
106573
.
13.
Wang
,
W. Z.
,
Chen
,
H.
,
Hu
,
Y. Z.
, and
Wang
,
H.
,
2006
, “
Effect of Surface Roughness Parameters on Mixed Lubrication Characteristics
,”
Tribol. Int.
,
39
(
6
), pp.
522
527
.
14.
Mu
,
S.
, and
Feng
,
X.
,
2012
, “
Analysis of Elastohydrodynamic Lubrication of Ball Screw With Rotating Nut
,”
Appl. Mech. Mater.
,
121–126
(
35
), pp.
3132
3139
. www.scientific.net/AMM.121-126.3132
15.
Sun
,
T.
,
Wang
,
M.
,
Gao
,
X.
, and
Zhao
,
Y.
,
2021
, “
Non-Hertzian Elastohydrodynamic Contact Stress Calculation of High-Speed Ball Screws
,”
Appl. Sci.
,
11
(
24
), p.
12801
.
16.
Zhang
,
Y.
,
Cui
,
P.
,
Yang
,
J.
,
Wang
,
Z.
, and
Pu
,
W.
,
2023
, “
Dynamic Grease Lubrication and Friction Behavior of Ball Screw Mechanism in High-Frequency Reciprocating Motion
,”
Tribol. Int.
,
178
(
2
), p.
108068
.
17.
Masjedi
,
M.
, and
Khonsari
,
M. M.
,
2015
, “
On the Effect of Surface Roughness in Point-Contact EHL: Formulas for Film Thickness and Asperity Load
,”
Tribol. Int.
,
82
(
2
), pp.
228
244
.
18.
Zhang
,
Y.
,
Zhou
,
C.
, and
Feng
,
H.
,
2023
, “
A Meticulous Friction Torque Model for a Lubricated Ball Screw Considering the Surface Roughness
,”
Tribol. Int.
,
190
(
14
), p.
109014
.
19.
Wang
,
Q. J.
,
Zhu
,
D.
,
Cheng
,
H. S.
,
Yu
,
T.
,
Jiang
,
X.
, and
Liu
,
S.
,
2004
, “
Mixed Lubrication Analyses by a Macro-Micro Approach and a Full-Scale Mixed EHL Model
,”
ASME J. Tribol.
,
126
(
1
), pp.
81
91
.
20.
Shen
,
J.-W.
,
Feng
,
H.-T.
,
Zhou
,
C.-G.
,
Chen
,
Z.-T.
, and
Ou
,
Y.
,
2022
, “
A New Two-Stage Degradation Model for the Preload of Ball Screws Considering Geometric Errors
,”
Wear
,
500–501
(
7
), p.
204352
.
21.
Zhou
,
C. G.
,
Xie
,
J. L.
, and
Feng
,
H. T.
,
2021
, “
Investigation of the Decompression Condition of Double-Nut Ball Screws Considering the Influence of the Geometry Error and Additional Elastic Unit
,”
Mech. Mach. Theory
,
156
(
2
), pp.
11
13
.
22.
Zhou
,
H.-X.
,
Zhou
,
C.-G.
,
Feng
,
H.-T.
, and
Ou
,
Y.
,
2020
, “
Theoretical and Experimental Analysis of the Preload Degradation of Double-Nut Ball Screws
,”
Precis. Eng.
,
65
(
5
), pp.
1
9
.
23.
Wu
,
J. J.
,
2000
, “
Simulation of Rough Surfaces With FFT
,”
Tribol. Int.
,
33
(
1
), pp.
47
58
.
24.
Yan
,
W.
,
Komvopoulos
,
K.
, and
Conry
,
T. F.
,
2001
, “
An Efficient Method for Computing Elastic-Plastic Asperity Contact Models in the Cold Rolling of Thin Films
,”
Fractals
,
9
(
9
), pp.
1791
1806
.
25.
Wang
,
Y.
,
Azam
,
A.
,
Wilson
,
M. C. T.
,
Neville
,
A.
, and
Morina
,
A.
,
2022
, “
A Comparative Study for Selecting and Using Simulation Methods of Gaussian Random Surfaces
,”
Tribol. Int.
,
166
(
9
), p.
107347
.
26.
Hill
,
I. D.
,
Hill
,
R.
, and
Holder
,
R. L.
,
1976
, “
Algorithm AS 99: Fitting Johnson Curves by Moments
,”
Appl. Stat.
,
25
(
2
), p.
180
.
27.
Ai
,
X.
,
1993
, “
Numerical Analyses of Elastohydrodynamically Lubricated Line and Point Contacts with Rough Surfaces by Using Semi-System and Multigrid Methods
,” Ph.D. dissertation, Northwestern University, Evanston, IL.
28.
Zhu
,
D.
, and
Hu
,
Y. Z.
,
2001
, “
A Computer Program Package for the Prediction of EHL and Mixed Lubrication Characteristics, Friction, Subsurface Stresses and Flash Temperatures Based on Measured 3-D Surface Roughness
,”
Tribol. Trans.
,
44
(
3
), pp.
383
390
.
29.
Ball Screws
,
1977
,
ISO 3408-3:2006: Ball Screws—Part 3: Acceptance Conditions and Acceptance Tests
.
3
. https://www.iso.org/standard/35023.html.
You do not currently have access to this content.