Extrusion-based elastomer seals are used in many applications, such as the seal in a variable bore ram valve used in offshore oil and gas drilling. Performing full-scale closing pressure experiments of such valves to characterize the seal performance and material failure of elastomer, especially under various temperature conditions, are quite expensive and time consuming. Conversely, simple coupon tests to characterize the elastomer mechanical properties and failure do not capture the complex deformation associated with the extrusion and subsequent sealing type that these materials undergo in the valves. In view of this, a simple subscale experimental test method capable of simulating the extrusion and sealing type deformation is developed. The extrusion and sealing deformation are realized by bonding the rectangular elastomer sample to metal pieces on top and bottom surfaces, and then compressing the sample in the vertical direction, while the deformation of the three lateral surfaces is kept constrained. As a result, sample deforms and extrudes out of the front surface, eventually forming the seal against a flat rigid metal plate placed at an appropriate distance. Simple scaling rules to determine the appropriate sample size and initial sealing gap, equivalent to the full-scale valve in terms of similar strain conditions, are derived and then verified using finite element analysis (FEA). Finally, the experimental test method is demonstrated by characterizing the contact pressure of nitrile (NBR) samples under different operating temperatures, ranging from 21 °C to 160 °C using pressure-sensitive film sensor.

References

1.
Lindley
,
P.
,
1966
, “
Load-Compression Relationships of Rubber Units
,”
J. Strain Anal. Eng. Des.
,
1
(
3
), pp.
190
195
.
2.
Green
,
I.
, and
English
,
C.
,
1992
, “
Analysis of Elastomeric o-Ring Seals in Compression Using the Finite Element Method
,”
Tribol. Trans.
,
35
(
1
), pp.
83
88
.
3.
Raparelli
,
T.
,
Bertetto
,
A. M.
, and
Mazza
,
L.
,
1997
, “
Experimental and Numerical Study of Friction in an Elastomeric Seal for Pneumatic Cylinders
,”
Tribol. Int.
,
30
(
7
), pp.
547
552
.
4.
Belforte
,
G.
,
Manuello
,
A.
, and
Mazza
,
L.
,
2006
, “
Optimization of the Cross Section of an Elastomeric Seal for Pneumatic Cylinders
,”
ASME J. Tribol.
,
128
(
2
), pp.
406
413
.
5.
Xue-Guan
,
S.
,
Lin
,
W.
, and
Young-Chul
,
P.
,
2009
, “
Analysis and Optimization of Nitrile Butadiene Rubber Sealing Mechanism of Ball Valve
,”
Trans. Nonferrous Met. Soc. China
,
19
, pp. s
220
s224
.
6.
Belforte
,
G.
,
Conte
,
M.
,
Bertetto
,
A. M.
,
Mazza
,
L.
, and
Visconte
,
C.
,
2009
, “
Experimental and Numerical Evaluation of Contact Pressure in Pneumatic Seals
,”
Tribol. Int.
,
42
(
1
), pp.
169
175
.
7.
Zhou
,
Y.
,
Huang
,
Z.
,
Bu
,
Y.
,
Qiu
,
C.
, and
Yuan
,
Y.
,
2014
, “
Simulation Studies on Drilling Mud Pump Plunger Seal Failure Under Ultrahigh Pressure and Ultradeep Conditions
,”
Eng. Failure Anal.
,
45
, pp.
142
150
.
8.
Lorenz
,
B.
, and
Persson
,
B. N. J.
,
2010
, “
Leak Rate of Seals: Effective-Medium Theory and Comparison With Experiment
,”
Eur. Phys. J. E
,
31
(
2
), pp.
159
167
.
9.
Lorenz
,
B.
,
Oh
,
Y.
,
Nam
,
S.
,
Jeon
,
S.
, and
Persson
,
B.
,
2015
, “
Rubber Friction on Road Surfaces: Experiment and Theory for Low Sliding Speeds
,”
J. Chem. Phys.
,
142
(
19
), p.
194701
.
10.
Kaisong
,
L. J. W.
,
1997
, “
Calculation of Sealing Parameters of Rubber Cores for Ram Blowout Preventers and Their Structural Optimization [j]
,”
Acta Pet. Sin.
,
18
(
1
), pp.
123
128
.
11.
Gent
,
A.
, and
Lindley
,
P.
,
1959
, “
The Compression of Bonded Rubber Blocks
,”
Proc. Inst. Mech. Eng.
,
173
(
1
), pp.
111
122
.
12.
Hailong
,
F.
,
Jinyou
,
W.
, and
Guangzheng
,
J.
,
2008
, “
Finite Element Analysis of Key Components of Ram Blowout Preventer Operating Under Pressure
,”
China Pet. Mach.
,
8
, p.
6
.
13.
Shi
,
Q.
,
Zhu
,
W.
, and
Ji
,
X.
,
2010
, “
Finite Element Analysis on Rubber Core and Perfect Design on Structure of the 2fz1821 Ram Blowout Preventer
,”
Drill. Prod. Technol.
,
6
, p.
28
.
14.
Banks
,
H.
,
Pinter
,
G. A.
, and
Yeoh
,
O.
,
2002
, “
Analysis of Bonded Elastic Blocks
,”
Math. Comput. Modell.
,
36
(
7
), pp.
875
888
.
15.
Suh
,
J. B.
, and
Kelly
,
S. G.
,
2011
, “
Stress Response of a Rubber Block Under Vertical Loading
,”
J. Eng. Mech.
,
138
(
7
), pp.
770
783
.
16.
Liggins
,
A.
,
1997
, “
The Practical Application of Fuji Prescale Pressure-Sensitive Film
,”
Optical Measurement Methods in Biomechanics
,
Springer
,
Berlin
, pp.
173
189
.
17.
Singerman
,
R.
,
Pedersen
,
D.
, and
Brown
,
T.
,
1987
, “
Quantitation of Pressure-Sensitive Film Using Digital Image Scanning
,”
Exp. Mech.
,
27
(
1
), pp.
99
105
.
18.
Dassault Systèmes
,
2007
,
Abaqus 6.7 Documentation
,
Dassault Systèmes
,
Providence, RI
.
19.
Marlow
,
R.
,
2003
, “
A General First-Invariant Hyperelastic Constitutive Model
,”
Constitutive Models for Rubber
,
CRC Press
,
Boca Raton / Balkema, Netherlands
, pp.
157
160
.
You do not currently have access to this content.