Abstract

Models for thermohydrodynamic lubrication in the turbulent regime are developed for a mechanical end face seal with various combinations of asperity height and roughness pattern. A surface wear model, based on deformation, is established for mixed lubrication such that the displacement is at most equal to the mean asperity height. Only normal load is involved in the solution of asperity deformation, and the mean film thickness is determined based on a total volume conservation hypothesis, in conjunction with an elastic-exponential hardening model. The singularity problem, present in the expected form of the Reynolds equation for a seal surface with circumferentially-oriented roughness grain sphere grooves, is avoided by viewing the seal roughness as porous material, thereby introducing roughness permeability. Flow permeability is thus obtained by combining Darcy’s law for porous material with the average flow model developed by Patir and Cheng for mixed lubrication. The hydrodynamic pressure and thereby the hydrodynamic load support are relatively higher from a seal with radially-oriented roughness. Both the mean film thickness and the hydrodynamic load support are substantially elevated by increasing the composite rms roughness, raising the inlet-flow pressure, and decreasing the rotational speed. Good agreement has been obtained from the comparison between the results herein and Lebeck’s experimental results.

Issue Section:
Research Papers
Topics:
Lubrication, Turbulence, Surface roughness, Flow (Dynamics), Stress, Deformation, Film thickness, Permeability, Porous materials, Pressure, Composite materials, Darcy's law, Displacement, Hardening, Thermohydrodynamics, Wear
1.
Bejan, A., 1985, Convection Heat Transfer, Wiley, New York.
2.
Cheng, H. S., and Snapp, R. B., 1967, “A Study of the Radial Film and Pressure Distribution of High Pressure Face Seals,” presented at the British Hydro-Mechanics Research Association, Third International Conference on Fluid Sealing, Cambridge, England, Paper No. E-3.
3.
Chowdhury
S. J.
,
1979
, “
Thermohydrodynamic Analysis of Journal Bearings
,”
ASME JOURNAL OF LUBRICATION TECHNOLOGY
, Vol.
101
, p.
21
21
.
4.
Christensen
H.
,
1969–70
, “
Stochastic Models for Hydrodynamic Lubrication of Rough Surfaces
,”
Proc. Instn. Mech. Engrs.
, Vol.
184
, pp.
1013
–
1026
.
5.
Christensen, H., and Tonder, K., 1969, “Tribology of Rough Surfaces: Stochastic Models of Hydrodynamic Lubrication,” SINTEF Rep., No. 22/69–78.
6.
Darcy, H., 1856, Les Frontaines Publiques de la Ville de Dijon, Dalmont, Paris.
7.
Dittus, F. W., and Boelter, M. K., Univ. Calif., Berkeley, Publ. Eng. 2:433 (1961).
8.
Findley, J. A., 1968, “Cavitation in Mechanical Face Seals,” ASME JOURNAL OF LUBRICATION TECHNOLOGY, pp. 356–364.
9.
Hamilton, D. B., Walowit, J. A., and Allen, C. M., 1966, “A Theory of Lubrication by Microirregularities,” ASME JOURNAL OF BASIC ENGINEERING, pp. 177–185.
10.
Lebeck, A. O., 1974, “Waviness Distortion and Wear in Mechanical Face Seals,” Report No. ME-64(74) NSF-271–1, The University of New Mexico, College of Engineering, Bureau of Engineering Research, Albuquerque, NM.
11.
Lebeck
A. O.
,
1980
, “
A Mixed Friction Hydrostatic Face Seal Model with Phase Change
,”
ASME JOURNAL OF LUBRICATION TECHNOLOGY
, Vol.
102
, pp.
133
–
138
.
12.
Lebeck
A. O.
,
Teale
J. L.
, and
Pierce
R. E.
,
1978
, “
Hydrodynamic Lubrication and Wear in Wavy Contacting Face Seal
,”
ASME JOURNAL OF LUBRICATION TECHNOLOGY
, Vol.
100
, pp.
81
–
91
.
13.
Ludwig, L. P., 1976, “Face Seal Lubrication I-Proposed and Published Models,” NASA Technical Note, NASA TND-8101.
14.
Metcalfe
R.
,
1978
, “
Predicted Effects of Sealing Gap Convergence on Performance of Plain End Face Seals
,”
ASLE
, Vol.
21
, pp.
124
–
142
.
15.
Ng, C. W., and Pan, C. H. T., 1965, “A Linearized Turbulent Lubrication Theory,” ASME Journal of Basic Engineering, pp. 675–688.
16.
Orcutt, F. K., Bell, J. C., Glaeser, W. A., and Allen, C. M., 1962, “Summary Report on the Dynamic Behavior of High Speed Liquid-Lubricated Face Seals to the Rotating Shaft Seal Research Group,” Jan. 24, Battle Memorial Institute, Columbus.
17.
Patir
N.
, and
Cheng
H. S.
,
1978
, “
An Average Flow Model for Determining Effects of Three Dimensional Roughness on Partial Hydrodynamic Lubrication
,”
ASME JOURNAL OF LUBRICATION TECHNOLOGY
, Vol.
100
, pp.
12
–
17
.
18.
Pullen
J.
, and
Williamson
J. B. P.
,
1972
, “
On the Plastic Contact of Rough Surfaces
,”
Proceedings Royal Society, London
, Series A, Vol.
327
, pp.
159
–
173
.
19.
Reichardt
H.
,
1951
, “
Vollstandige Darstellung der Turbulenten Geschwindigh-eitverteilung in Glatten Leitungen
,”
Z Angew. Math. Mech.
, Vol.
31
, p.
208
208
.
20.
Rohde, S. M., 1980, “A Mixed Friction Model for Dynamically Loaded Contacts with Application to Piston Ring Lubrication,” The Winter Annual Meeting of ASME, Chicago, Nov. 16–21.
21.
Snapp, R. B., and Sasdelli, K. R., 1973, “Performance Characteristics of a High Pressure Face Seal with Radially Converging Interface Shapes,” Paper E4, 6th International Conference on Fluid Sealing, Feb. 27–Mar. 2, Munich.
22.
Stanghan-Batch
B. A.
,
1971
, “
Face Lubrication in Mechanical Face Seals
,”
Instn. Mech. Engrs.
, Vol.
c59/71
, pp.
54
–
59
.
23.
Tonder
K.
, and
Christensen
H.
,
1972
, “
Waviness and Roughness in Hydrodynamic Lubrication
,”
Proc. Instn. Mech. Engrs.
, Vol.
186
, pp.
72
–
77
.
24.
Uppal
A. H.
, and
Probert
S. D.
,
1973
, “
The Plastic Contact Between a Rough and a Flat Surface
,”
Wear
, Vol.
23
, pp.
173
–
184
.
25.
Washizu, K. (ed.), 1982, Variational Methods in Elasticity and Plasticity, Pergamon Press, Oxford, UK.
26.
Williamson
J. P. B.
, and
Hunt
R. T.
,
1972
, “
Asperity Persistence and the Real Area of Contact between Rough Surface
,”
Proceedings Royal Society, London
, A, Vol.
327
, pp.
147
–
157
.
This content is only available via PDF.
Copyright © 1996
 by The American Society of Mechanical Engineers
You do not currently have access to this content.