Abstract
Nanoliquid impingement heat transfer with a phase change material (PCM) installed radial system is considered. The study is performed by using the finite element method for various values of Reynolds numbers (100 ≤ Re ≤ 300), height of PCM (0.25H ≤ hpcm ≤ 0.75H), and plate spacing (0.15H ≤ hs ≤ 0.40H). Different configurations using water, nanoliquid, and nanoliquid + PCM are compared in terms of heat transfer improvement. Thermal performance is improved by using PCM, while best performance is achieved with nanoliquid and PCM-installed configuration. At Re = 100 and Re = 300, heat transfer improvements of 26 and 25.5 are achieved with the nanoliquid + PCM system as compared to water without PCM. The height of the PCM layer also influences the heat transfer dynamic behavior, while there is 12.6 variation in the spatial average heat transfer of the target surface with the lowest and highest PCM heights while discharging time increases by about 76.5. As the spacing between the plates decreases, average heat transfer rises and there is 38 variation.
Issue Section:
Research Papers
References
1.
Ekkad
, S. V.
, and Singh
, P.
, 2021
, “A Modern Review on Jet Impingement Heat Transfer Methods
,” ASME J. Heat Transfer-Trans. ASME
, 143
(6
), p. 064001
. 2.
Chen
, Z.
, Shahsavar
, A.
, Al-Rashed
, A. A.
, and Afrand
, M.
, 2020
, “The Impact of Sonication and Stirring Durations on the Thermal Conductivity of Alumina-Liquid Paraffin Nanofluid: An Experimental Assessment
,” Powder. Technol.
, 360
, pp. 1134
–1142
. 3.
Oztop
, H. F.
, Varol
, Y.
, Koca
, A.
, Firat
, M.
, Turan
, B.
, and Metin
, I.
, 2011
, “Experimental Investigation of Cooling of Heated Circular Disc Using Inclined Circular Jet
,” Int. Commun. Heat Mass Transfer
, 38
(7
), pp. 990
–1001
. 4.
Han
, B.
, and Goldstein
, R. J.
, 2001
, “Jet-Impingement Heat Transfer in Gas Turbine Systems
,” Ann. N.Y. Acad. Sci.
, 934
(1
), pp. 147
–161
. 5.
Nadda
, R.
, Kumar
, A.
, and Maithani
, R.
, 2018
, “Efficiency Improvement of Solar Photovoltaic/Solar Air Collectors by Using Impingement Jets: A Review
,” Renewable. Sustainable. Energy. Rev.
, 93
, pp. 331
–353
. 6.
Dewan
, A.
, Dutta
, R.
, and Srinivasan
, B.
, 2012
, “Recent Trends in Computation of Turbulent Jet Impingement Heat Transfer
,” Heat. Transfer. Eng.
, 33
(4–5
), pp. 447
–460
. 7.
Garimella
, S. V.
, 2000
, “Heat Transfer and Flow Fields in Confined Jet Impingement
,” Annu. Rev. Heat Transfer
, 11
, pp. 413
–494
. 8.
Maghrabie
, H. M.
, 2021
, “Heat Transfer Intensification of Jet Impingement Using Exciting Jets-A Comprehensive Review
,” Renewable. Sustainable. Energy. Rev.
, 139
, p. 110684
. 9.
Babar
, H.
, and Ali
, H. M.
, 2019
, “Airfoil Shaped Pin-Fin Heat Sink: Potential Evaluation of Ferric Oxide and Titania Nanofluids
,” Energy. Convers. Manage.
, 202
, p. 112194
. 10.
Chamkha
, A. J.
, Molana
, M.
, Rahnama
, A.
, and Ghadami
, F.
, 2018
, “On the Nanofluids Applications in Microchannels: A Comprehensive Review
,” Powder. Technol.
, 332
, pp. 287
–322
. 11.
Tayebi
, T.
, and Chamkha
, A. J.
, 2020
, “Magnetohydrodynamic Natural Convection Heat Transfer of Hybrid Nanofluid in a Square Enclosure in the Presence of a Wavy Circular Conductive Cylinder
,” ASME J. Thermal Sci. Eng. Appl.
, 12
(3
), p. 031009
. 12.
Rashad
, A. M.
, Chamkha
, A. J.
, Ismael
, M. A.
, and Salah
, T.
, 2018
, “Magnetohydrodynamics Natural Convection in a Triangular Cavity Filled With a Cu-Al2O3/Water Hybrid Nanofluid With Localized Heating From Below and Internal Heat Generation
,” ASME J. Heat Transfer-Trans. ASME
, 140
(7
), p. 072502
. 13.
Arshad
, W.
, and Ali
, H. M.
, 2017
, “Experimental Investigation of Heat Transfer and Pressure Drop in a Straight Minichannel Heat Sink Using TiO2 Nanofluid
,” Int. J. Heat. Mass. Transfer.
, 110
, pp. 248
–256
. 14.
Izadi
, A.
, Siavashi
, M.
, Rasam
, H.
, and Xiong
, Q.
, 2020
, “MHD Enhanced Nanofluid Mediated Heat Transfer in Porous Metal for CPU Cooling
,” Appl. Therm. Eng.
, 168
, p. 114843
. 15.
Chamkha
, A. J.
, Miroshnichenko
, I. V.
, and Sheremet
, M. A.
, 2017
, “Numerical Analysis of Unsteady Conjugate Natural Convection of Hybrid Water-Based Nanofluid in a Semicircular Cavity
,” ASME J. Thermal Sci. Eng. Appl.
, 9
(4
), p. 041004
. 16.
Javed
, S.
, Ali
, H. M.
, Babar
, H.
, Khan
, M. S.
, Janjua
, M. M.
, and Bashir
, M. A.
, 2020
, “Internal Convective Heat Transfer of Nanofluids in Different Flow Regimes: A Comprehensive Review
,” Physica A: Statist. Mech. Appl.
, 538
, p. 122783
. 17.
Baïri
, A.
, 2019
, “Experimental Study on Enhancement of Free Convective Heat Transfer in a Tilted Hemispherical Enclosure by Using Water-ZnO Nanofluid Saturated Porous Materials
,” Appl. Therm. Eng.
, 148
, pp. 992
–998
. 18.
Sheikholeslami
, M.
, and Rokni
, H. B.
, 2017
, “Magnetohydrodynamic CuO–Water Nanofluid in a Porous Complex-Shaped Enclosure
,” ASME J. Thermal Sci. Eng. Appl.
, 9
(4
), p. 041007
. 19.
Taherian
, H.
, Alvarado
, J. L.
, and Languri
, E. M.
, 2018
, “Enhanced Thermophysical Properties of Multiwalled Carbon Nanotubes Based Nanofluids. Part 1: Critical Review
,” Renewable. Sustainable. Energy. Rev.
, 82
(3
), pp. 4326
–4336
. 20.
Mahian
, O.
, Kolsi
, L.
, Amani
, M.
, Estellé
, P.
, Ahmadi
, G.
, Kleinstreuer
, C.
, Marshall
, J. S.
, et al., 2019
, “Recent Advances in Modeling and Simulation of Nanofluid Flows-Part I: Fundamentals and Theory
,” Phys. Rep.
, 790
, pp. 1
–48
. 21.
Faraji
, H.
, Faraji
, M.
, and El Alami
, M.
, 2020
, “Numerical Survey of the Melting Driven Natural Convection Using Generation Heat Source: Application to the Passive Cooling of Electronics Using Nano-enhanced Phase Change Material
,” ASME J. Thermal Sci. Eng. Appl.
, 12
(2
), p. 021005
. 22.
Manca
, O.
, Mesolella
, P.
, Nardini
, S.
, and Ricci
, D.
, 2011
, “Numerical Study of a Confined Slot Impinging Jet With Nanofluids
,” Nanoscale. Res. Lett.
, 6
, p. 188
. 23.
Mohammadpour
, J.
, and Lee
, A.
, 2020
, “Investigation of Nanoparticle Effects on Jet Impingement Heat Transfer: A Review
,” J. Mol. Liq.
, 316
, p. 113819
. 24.
Li
, Q.
, Xuan
, Y.
, and Yu
, F.
, 2012
, “Experimental Investigation of Submerged Single Jet Impingement Using Cu-Water Nanofluid
,” Appl. Therm. Eng.
, 36
, pp. 426
–433
. 25.
Naphon
, P.
, Wiriyasart
, S.
, Arisariyawong
, T.
, and Nakharintr
, L.
, 2019
, “A Numerical and Experimental Analysis on the Jet Impingement Nanofluids Flow and Heat Transfer Characteristics in the Micro-Channel Heat Sink
,” Int. J. Heat. Mass. Transfer.
, 131
, pp. 329
–340
. 26.
Barewar
, S. D.
, Tawri
, S.
, and Chougule
, S. S.
, 2019
, “Heat Transfer Characteristics of Free Nanofluid Impinging Jet on Flat Surface With Different Jet to Plate Distance: An Experimental Investigation
,” Chem. Eng. Processing-Process Intensification
, 136
, pp. 1
–10
. 27.
Selimefendigil
, F.
, and Öztop
, H. F.
, 2020
, “Al2O3-Water Nanofluid Jet Impingement Cooling With Magnetic Field
,” Heat. Transfer. Eng.
, 41
(1
), pp. 50
–64
. 28.
Ahmadi
, H.
, Moghari
, R. M.
, Esmailpour
, K.
, and Mujumdar
, A.
, 2016
, “Numerical Investigation of Semi-Confined Turbulent Slot Jet Impingement on a Concave Surface Using an Al2O3–Water Nanofluid
,” Appl. Math. Model.
, 40
(2
), pp. 1110
–1125
. 29.
Selimefendigil
, F.
, and Öztop
, H. F.
, 2017
, “Jet Impingement Cooling and Optimization Study for a Partly Curved Isothermal Surface with CuO-Water Nanofluid
,” Int. Commun. Heat Mass Transfer
, 89
, pp. 211
–218
. 30.
Zahmatkesh
, I.
, and Ali Naghedifar
, S.
, 2017
, “Oscillatory Mixed Convection in the Jet Impingement Cooling of a Horizontal Surface Immersed in a Nanofluid-Saturated Porous Medium
,” Numer. Heat Transfer, Part A: Appl.
, 72
(5
), pp. 401
–416
. 31.
Izadi
, S.
, Armaghani
, T.
, Ghasemiasl
, R.
, Chamkha
, A. J.
, and Molana
, M.
, 2019
, “A Comprehensive Review on Mixed Convection of Nanofluids in Various Shapes of Enclosures
,” Powder. Technol.
, 343
, pp. 880
–907
. 32.
Zahmatkesh
, I.
, and Naghedifar
, S. A.
, 2018
, “Pulsating Nanofluid Jet Impingement Onto a Partially Heated Surface Immersed in a Porous Layer
,” Jordan J. Mech. Ind. Eng.
, 12
(2
), pp. 99
–107
.33.
Buonomo
, B.
, Manca
, O.
, Bondareva
, N. S.
, and Sheremet
, M. A.
, 2019
, “Thermal and Fluid Dynamic Behaviors of Confined Slot Jets Impinging on An Isothermal Moving Surface with Nanofluids
,” Energies
, 12
(11
), p. 2074
. 34.
Selimefendigil
, F.
, and Öztop
, H. F.
, 2018
, “Cooling of a Partially Elastic Isothermal Surface by Nanofluids Jet Impingement
,” ASME J. Heat Transfer-Trans. ASME
, 140
(4
), p. 042205
. 35.
Faraji
, H.
, Benkaddour
, A.
, Oudaoui
, K.
, El Alami
, M.
, and Faraji
, M.
, 2021
, “Emerging Applications of Phase Change Materials: A Concise Review of Recent Advances
,” Heat Transfer
, 50
(2
), pp. 1443
–1493
. 36.
Rostami
, S.
, Afrand
, M.
, Shahsavar
, A.
, Sheikholeslami
, M.
, Kalbasi
, R.
, Aghakhani
, S.
, Shadloo
, M. S.
, and Oztop
, H. F.
, 2020
, “A Review of Melting and Freezing Processes of PCM/nano-PCM and Their Application in Energy Storage
,” Energy
, 211
, p. 118698
. 37.
Selimefendigil
, F.
, and Öztop
, H. F.
, 2021
, “Effects of Using a Porous Disk on the Dynamic Features of Phase Change Process With PCM Integrated Circular Pipe During Nano-Liquid Forced Convection in Discharging Operation Mode
,” J. Taiwan Inst. Chem. Eng.
, 124
, pp. 381
–390
. 38.
Faraji
, H.
, El Alami
, M.
, and Arshad
, A.
, 2021
, “Investigating the Effect of Single and Hybrid Nanoparticles on Melting of Phase Change Material in a Rectangular Enclosure With Finite Heat Source
,” Int. J. Energy Res.
, 45
(3
), pp. 4314
–4330
. 39.
Leong
, K. Y.
, Rahman
, M. R. A.
, and Gurunathan
, B. A.
, 2019
, “Nano-Enhanced Phase Change Materials: A Review of Thermo-physical Properties, Applications and Challenges
,” J. Energy Storage
, 21
, pp. 18
–31
. 40.
Selimefendigil
, F.
, and Öztop
, H. F.
, 2021
, “Analysis of Hybrid Nanofluid and Surface Corrugation in the Laminar Convective Flow Through an Encapsulated PCM Filled Vertical Cylinder and POD-based Modeling
,” Int. J. Heat. Mass. Transfer.
, 178
, p. 121623
. 41.
Darzi
, A. A. R.
, Jourabian
, M.
, and Farhadi
, M.
, 2016
, “Melting and Solidification of PCM Enhanced by Radial Conductive Fins and Nanoparticles in Cylindrical Annulus
,” Energy. Convers. Manage.
, 118
, pp. 253
–263
. 42.
Mousavi
, S.
, Siavashi
, M.
, and Heyhat
, M. M.
, 2019
, “Numerical Melting Performance Analysis of a Cylindrical Thermal Energy Storage Unit Using Nano-Enhanced PCM and Multiple Horizontal Fins
,” Numer. Heat Transfer, Part A: Appl.
, 75
(8
), pp. 560
–577
. 43.
Sheikholeslami
, M.
, and Mahian
, O.
, 2019
, “Enhancement of PCM Solidification Using Inorganic Nanoparticles and an External Magnetic Field With Application in Energy Storage Systems
,” J. Cleaner. Prod.
, 215
, pp. 963
–977
. 44.
Mohammadnejad
, F.
, and Hossainpour
, S.
, 2020
, “A CFD Modeling and Investigation of a Packed Bed of High Temperature Phase Change Materials (PCMs) With Different Layer Configurations
,” J. Energy Storage
, 28
, p. 101209
. 45.
Nield
, D.
, and Bejan
, A.
, 2013
, Convection in Porous Media, in Convection Heat Transfer
, John Wiley & Sons
, Hoboken, NJ
.46.
COMSOL AB
, 2018
, COMSOL Multiphysics User's Guide, Stockholm, Sweden
.47.
Wakao
, N.
, Kaguei
, S.
, and Funazkri
, T.
, 1979
, “Effect of Fluid Dispersion Coefficients on Particle-to-fluid Heat Transfer Coefficients in Packed Beds: Correlation of Nusselt Numbers
,” Chem. Eng. Sci.
, 34
(3
), pp. 325
–336
. 48.
Timofeeva
, E. V.
, Routbort
, J. L.
, and Singh
, D.
, 2009
, “Particle Shape Effects on Thermophysical Properties of Alumina Nanofluids
,” J. Appl. Phys.
, 106
(1
), p. 014304
. 49.
Liu
, F.
, Cai
, Y.
, Wang
, L.
, and Zhao
, J.
, 2018
, “Effects of Nanoparticle Shapes on Laminar Forced Convective Heat Transfer in Curved Ducts Using Two-Phase Model
,” Int. J. Heat. Mass. Transfer.
, 116
, pp. 292
–305
. 50.
Arani
, A. A. A.
, Sadripour
, S.
, and Kermani
, S.
, 2017
, “Nanoparticle Shape Effects on Thermal-Hydraulic Performance of Boehmite Alumina Nanofluids in a Sinusoidal–Wavy Mini-Channel With Phase Shift and Variable Wavelength
,” Int. J. Mech. Sci.
, 128
, pp. 550
–563
. 51.
Ellahi
, R.
, Hassan
, M.
, and Zeeshan
, A.
, 2015
, “Shape Effects of Nanosize Particles in Cu–H2O Nanofluid on Entropy Generation
,” Int. J. Heat. Mass. Transfer.
, 81
, pp. 449
–456
. 52.
Manca
, O.
, Ricci
, D.
, Nardini
, S.
, and Di Lorenzo
, G.
, 2016
, “Thermal and Fluid Dynamic Behaviors of Confined Laminar Impinging Slot Jets With Nanofluids
,” Int. Commun. Heat Mass Transfer
, 70
, pp. 15
–26
. 53.
Chou
, Y.
, and Hung
, Y.
, 1994
, “Impingement Cooling of an Isothermally Heated Surface With a Confined Slot Jet
,” ASME J. Heat Transfer-Trans. ASME
, 116
(2
), pp. 479
–482
. 54.
Lamraoui
, H.
, Mansouri
, K.
, and Saci
, R.
, 2019
, “Numerical Investigation on Fluid Dynamic and Thermal Behavior of a Non-Newtonian Al2O3–Water Nanofluid Flow in a Confined Impinging Slot Jet
,” J. Non-Newtonian. Fluid. Mech.
, 265
, pp. 11
–27
. 55.
Chiriac
, V. A.
, and Ortega
, A.
, 2002
, “A Numerical Study of the Unsteady Flow and Heat Transfer in a Transitional Confined Slot Jet Impinging on An Isothermal Surface
,” Int. J. Heat. Mass. Transfer.
, 45
(6
), pp. 1237
–1248
. 56.
Wolff
, F.
, and Viskanta
, R.
, 1988
, “Solidification of a Pure Metal At a Vertical Wall in the Presence of Liquid Superheat
,” Int. J. Heat. Mass. Transfer.
, 31
(8
), pp. 1735
–1744
. 57.
Nallusamy
, N.
, Sampath
, S.
, and Velraj
, R.
, 2007
, “Experimental Investigation on a Combined Sensible and Latent Heat Storage System Integrated With Constant/Varying (Solar) Heat Sources
,” Renewable Energy
, 32
(7
), pp. 1206
–1227
. 58.
Chiriac
, V. A.
, and Ortega
, A.
, 2002
, “A Numerical Study of the Unsteady Flow and Heat Transfer in a Transitional Confined Slot Jet Impinging on an Isothermal Surface
,” Int. J. Heat. Mass. Transfer.
, 45
, pp. 1237
–1248
. Copyright © 2021 by ASME
You do not currently have access to this content.
