1-15 of 15
Keywords: temperature distribution
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Article Type: Research Papers
J. Pressure Vessel Technol. June 2011, 133(3): 031403.
Published Online: April 4, 2011
... fatigue cracks fatigue testing geometry plates (structures) stainless steel temperature distribution It has been recognized that crack initiation and propagation of fatigue and creep-fatigue test at elevated temperature are important to evaluate life prediction. Watanabe and Koike ( 1...
Journal Articles
Article Type: Research Papers
J. Pressure Vessel Technol. December 2009, 131(6): 061403.
Published Online: October 8, 2009
... of this paper is to investigate and understand the temperature distribution during EF welding. A one-dimensional transient heat-transfer model was proposed, taking the variation in the rate of power input, the phase transition of PE, and the thermal contact conductance between heating wire and PE...
Journal Articles
Article Type: Research Papers
J. Pressure Vessel Technol. November 2008, 130(4): 041206.
Published Online: August 21, 2008
... boundary conditions, a generalized series based on a new and infinitely differentiable polynomial was employed to inversely determine the transient temperature distribution in a semi-infinite slab using only a single temperature history. These temperature distributions were in turn used to find...
Journal Articles
Article Type: Research Papers
J. Pressure Vessel Technol. August 2008, 130(3): 031203.
Published Online: June 12, 2008
.... This paper employs the continuous-time analog Hopfield neural network (CHNN) to compute the temperature distribution in various forward heat conduction problems. An efficient technique is then proposed for the solution of inverse heat conduction problems using a three-layered backpropagation neural network...
Journal Articles
Article Type: Research Papers
J. Pressure Vessel Technol. February 2008, 130(1): 011201.
Published Online: January 8, 2008
... ). The direct route addresses failure modes directly, having, therefore, advantages in comparison to the traditional method, which is stress categorization. Special attention is given to the progressive plastic deformation design check (PD-DC) with space and time-dependent temperature distribution...
Journal Articles
Article Type: Research Papers
J. Pressure Vessel Technol. May 2007, 129(2): 313–315.
Published Online: November 20, 2006
... the carbon steel from exposure to excessive temperatures. The temperature distribution in the steel tube-sheet–tube-ferrule system is affected by process gas flow and heat transfer through the assembly. Rather than depend on “assumed” heat transfer coefficients and fluid flow distribution, a computational...
Journal Articles
Article Type: Research Papers
J. Pressure Vessel Technol. November 2007, 129(4): 583–592.
Published Online: October 29, 2006
... a comparison of the predicted time-averaged temperature distributions by the three models with the experimental data at six vertical locations. It is shown that the V2-f model best predicts the time-averaged temperature distributions. All the models predict similar temperature distributions near the inlet...
Journal Articles
Article Type: Research Papers
J. Pressure Vessel Technol. November 2005, 127(4): 394–401.
Published Online: May 29, 2005
.... Temperature distribution and thermal distortion in 52 in. HE cover plate at Δ T = 400 ° C The bolt load change due to temperature requires the knowledge of both the radial and axial displacements of the individual flange components. The thermal profile and the axial...
Journal Articles
Article Type: Article
J. Pressure Vessel Technol. February 2005, 127(1): 7–12.
Published Online: March 15, 2005
.... Knowledge of the thermal history and temperature distributions are thus critical in developing control schemes for acceptable residual stress distributions to improve in-service component behavior. A comprehensive study of three-dimensional temperature distributions in a stainless steel tee branch junction...
Journal Articles
Article Type: Technical Papers
J. Pressure Vessel Technol. May 2003, 125(2): 131–135.
Published Online: May 5, 2003
... = range of stress intensity factor P max = maximum load 1 Thermal stress due to the temperature distribution in center cracked type specimen can be reduced down to about −1 MPa by using specially designed long furnace and slit specimen. 2 The fatigue crack propagation...
Journal Articles
Article Type: Technical Papers
J. Pressure Vessel Technol. August 2001, 123(3): 391–397.
Published Online: February 28, 2001
... February 28, 2001. Associate Editor: C. E. Jaske. 17 April 2000 28 February 2001 boilers oxidation steel pressure vessels temperature distribution The demand for increased efficiency in a power generation plant is becoming greater in order to diminish global environmental...
Journal Articles
Article Type: Technical Papers
J. Pressure Vessel Technol. February 2001, 123(1): 88–96.
Published Online: October 27, 2000
... . Manuscript received by the PVP Division, January, 2000; revised manuscript received October 27, 2000. Editor: S. Y. Zamrik. 01 August 1999 01 January 2000 27 October 2000 steel oxidation temperature distribution iron compounds oxygen compounds air molybdenum alloys...
Journal Articles
Article Type: Technical Papers
J. Pressure Vessel Technol. May 2001, 123(2): 173–178.
Published Online: October 20, 2000
... 10 11 . pressure vessels temperature distribution fatigue fatigue cracks strain measurement 2001 ASME ...
Journal Articles
Article Type: Technical Papers
J. Pressure Vessel Technol. February 2001, 123(1): 146–149.
Published Online: August 21, 2000
... of the temperature distribution as a function of time and radial position was then used to derive new relationships for the transient thermoelastic stress states. The derived expressions allow an easy analysis of the significance of the exponential terms and convective coefficient in determining the magnitudes...
Journal Articles
Article Type: Technical Papers
J. Pressure Vessel Technol. May 2000, 122(2): 130–138.
Published Online: January 27, 2000
... by a traveling temperature distribution. In this paper, the mechanism of this ratcheting is proposed, and the evaluation method of ratcheting strain is shown based on this mechanism. The proposed evaluation method is basically based on the hoop-membrane stress due to the axial temperature distribution...