Fast fracture in cannons can be well described using elastic-plastic fracture toughness, in combination with comparisons of cannon section size relative to the size required to maintain plane strain fracture. Fatigue fracture of cannon tubes is modeled from results of full-size fatigue tests that simulate cannon firing. These tests are also the basis of fatigue-intensity-factor modeling of fatigue life, which incorporates material strength, initial crack size and Bauschinger-modified autofrettage residual stress into life predictions. Environment-assisted fracture in the thermally damaged near-bore region of fired cannons is shown to be controlled by hydrogen. High strength cannon steels are susceptible to hydrogen; cannon propellant gases provide the hydrogen; and the source of sustained tensile stress is the near-bore thermal damage and compressive yielding. A thermo-mechanical model predicts tensile residual stress of similar depth to that of observed hydrogen cracks. Coating fracture in the thermal-damage region of fired cannons is characterized and modeled. The Evans/Hutchinson slip zone concept is extended to calculate in-situ coating fracture strength from observed crack spacing and hardness in the damaged region.

Issue Section:
Technical Papers
Keywords:
weapons, critical phenomena, fracture toughness, elastoplasticity, Bauschinger effect, tensile strength, thermal barrier coatings, fatigue cracks, steel
Topics:
Artillery, Fracture (Materials), Fracture (Process), Steel, Fatigue life, Fracture toughness, Stress, Fatigue
1.
Davidson, T. E., Throop, J. F., and Underwood, J. H., 1977, “Failure of a 175 mm Tube and the Resolution of the Problem Using an Autofrettaged Design,” Case Studies in Fracture Mechanics, T. P. Rich and D. J. Cartwright, Eds., Army Materials and Mechanics Research Center, Watertown, MA, pp. 3.9.1–13.
2.
ASTM E1820, Standard Test Method for Measurement of Fracture Toughness, 2000, Annual Book of ASTM Standards, Vol. 03.01, American Society for Testing and Materials, West Conshohocken, PA, pp. 1000–1033.
3.
ASTM E23, Standard Test Methods E23 for Notched Bar Impact Testing of Metallic Materials, 2000, Annual Book of ASTM Standards, Vol. 03.01, American Society for Testing and Materials, West Conshohocken, PA, pp. 138–162.
4.
Underwood
,
J. H.
,
Farrara
,
R. A.
, and
Audino
,
M. J.
,
1994
, “
Yield-Before-Break Fracture Mechanics Analysis of High Strength Steel Pressure Vessels
,”
ASME J. Pressure Vessel Technol.
,
117
, pp.
79
–
84
.
5.
Underwood, J. H., and Audino, M. A., 1998, “Effects of Initial Cracks and Firing Environment on Cannon Fatigue Life,” Fatigue Design 1998, Vol. II, Technical Research Center of Finland, Espoo, Finland, pp. 491–500.
6.
Underwood, J. H., and Parker, A. P., 1997, “Fatigue Life Assessment of Steel Pressure Vessels With Varying Stress Concentration, Residual Stress and Initial Cracks,” Advances in Fracture Research, Proceedings of ICF9, Pergamon, New York, pp. 215–226.
7.
Parker
,
A. P.
,
2001
, “
Autofrettage of Open-End Tubes-Pressures, Stresses, Strains and Code Comparisons
,”
ASME J. Pressure Vessel Technol.
,
123
, pp.
271
–
281
.
8.
Troiano, E., Parker, A. P., Underwood, J. H., and Mossey, C., 2002, “Experimental Data, Numerical Fit and Life Approximations Relating to the Bauschinger Effect in High Strength Armament Steels,” Proceedings of Gun Tubes 2002, 15–18 September 2002, Oxford, England, in press.
9.
Underwood, J. H., Parker, A. P., Troiano, E., Vigilante, G. N., and Witherell, M. D., 2001, “Fatigue and Hydrogen Cracking in Cannons With Mechanical and Thermal Residual Stress,” Advances in Fracture Research, Proceedings of ICF10, Pergamon, New York.
10.
Underwood, J. H., Parker, A. P., Vigilante, G. N., and Cote, P. J., 2002, “Thermal Damage, Cracking and Rapid Erosion of Cannon Bore Coatings,” Proceedings of Gun Tubes 2002, 15–18 September 2002, Oxford, England, in press.
11.
Cote
,
P. J.
,
Kendall
,
G.
, and
Todaro
,
M. E.
,
2001
, “
Laser Pulse Heating of Gun Bore Coatings
,”
Surf. Coat. Technol.
,
146–147
, pp.
65
–
69
.
12.
Vigilante
,
G. N.
,
Underwood
,
J. H.
,
Crayon
,
D.
,
Tauscher
,
S. S.
,
Sage
,
T.
, and
Troiano
,
E.
, 1997, “Hydrogen Induced Cracking Tests of High Strength Steels and Nickel-Iron Base Alloys Using the Bolt-Loaded Specimen,” Fatigue and Fracture Mechanics, ASTM STP, 1321, ASTM, West Conshohocken, PA, pp. 602–616.
13.
Underwood
,
J. H.
,
Parker
,
A. P.
,
Cote
,
P. J.
, and
Sopok
,
S.
,
1999
, “
Compressive Thermal Yielding Leading to Hydrogen Cracking in a Fired Cannon
,”
ASME J. Pressure Vessel Technol.
,
121
, pp.
116
–
120
.
14.
Evans
,
A. G.
, and
Hutchinson
,
J. W.
,
1995
, “
The Thermomechanical Integrity of Thin Films and Multilayers
,”
Acta Metall. Mater.
,
43
, pp.
2507
–
2530
.
Copyright © 2003
 by ASME
You do not currently have access to this content.