Cycloid drives are compact, efficient speed reducers. In this paper, a unified set of equations is presented to optimize their design. The conceptual framework and profile design are described. Sources and effects of tolerance are then introduced, including profile reduction, backlash and torque ripple, and maximum gear-ratio. Equations for stress, efficiency, and moment of inertia are provided.
Issue Section:
Technical Briefs
1.
Hashimoto
, M.
, Kiyosawa
, Y.
, and Paul
, R. P.
, 1993, “A Torque Sensing Technique for Robots With Harmonic Drives
,” IEEE Trans. Rob. Autom.
1042-296X, 9
, pp. 108
–116
.2.
Kennedy
, C. W.
, and Desai
, J. P.
, 2003, “Estimation and Modeling of the Harmonic Drive Transmission in the Mitsubishi PA-10 Robot Arm
,” IEEE International Conference on Intelligent Robotics and Systems
, Las Vegas, NV.3.
Albu-Schaffer
, A.
, Eiberger
, O.
, Grebenstein
, M.
, Haddadin
, S.
, Ott
, C.
, Wimbock
, T.
, Wolf
, S.
, and Hirzinger
, G.
, 2008, “Soft Robotics—From Torque Feedback-Controlled Lightweight Robots to Intrinsically Compliant Systems
,” IEEE Rob. Autom. Mag.
1070-9932, 15
, pp. 20
–30
.4.
Shin
, J. H.
, and Kwon
, S. M.
, 2006, “On the Lobe Profile Design in a Cycloid Reducer Using Instant Velocity Center
,” Mech. Mach. Theory
0094-114X, 41
, pp. 596
–616
.5.
Gorla
, C.
, Davoli
, P.
, Rosa
, F.
, Longoni
, C.
, Chiozzi
, F.
, and Samarani
, A.
, 2008, “Theoretical and Experimental Analysis of a Cycloidal Speed Reducer
,” ASME J. Mech. Des.
0161-8458, 130
, p. 112604
.6.
Hwang
, Y. W.
, and Hsieh
, C. F.
, 2007, “Geometric Design Using Hypotrochoid and Nonundercutting Conditions for an Internal Cycloidal Gear
,” ASME J. Mech. Des.
0161-8458, 129
, pp. 413
–420
.7.
Mimmi
, G. C.
, and Pennacchi
, P. E.
, 2000, “Non-Undercutting Conditions in Internal Gears
,” Mech. Mach. Theory
0094-114X, 35
, pp. 477
–490
.8.
Ye
, Z. H.
, Zhang
, W.
, Huang
, Q. H.
, and Chen
, C. M.
, 2006, “Simple Explicit Formulae for Calculating Limit Dimensions to Avoid Undercutting in the Rotor of a Cycloid Rotor Pump
,” Mech. Mach. Theory
0094-114X, 41
, pp. 405
–414
.9.
Chen
, B.
, Fang
, T. T.
, Li
, C. Y.
, and Wang
, S. Y.
, 2008, “Gear Geometry of Cycloid Drives
,” Sci. China, Ser. E: Technol. Sci.
1006-9321, 51
, pp. 598
–610
.10.
Shigley
, J. E.
, Mischke
, C. R.
, and Budynas
, R. G.
, 2004, Mechanical Engineering Design
, 7th ed., McGraw-Hill
, New York
.11.
Yang
, D. C. H.
, and Blanch
, J. G.
, 1990, “Design and Application Guidelines for Cycloid Drives With Machining Tolerances
,” Mech. Mach. Theory
0094-114X, 25
, pp. 487
–501
.12.
Harnoy
, A.
, 2002, Bearing Design in Machinery: Engineering Tribology and Lubrication
, CRC
, New York, NY
.13.
Li
, X.
, He
, W. D.
, Li
, L. X.
, and Schmidt
, L. C.
, 2004, “A New Cycloid Drive With High-Load Capacity and High Efficiency
,” ASME J. Mech. Des.
0161-8458, 126
, pp. 683
–686
.Copyright © 2010
by American Society of Mechanical Engineers
You do not currently have access to this content.
