Several 3-DOF pure translational parallel manipulators have been reported recently. However, kinematic conditions of such translational parallel manipulators have not been studied deeply. Most previously reported translational parallel manipulators were analyzed by considering constraints on the motion of an independent leg. In addition to the constraints of independent legs, the effect of the constraints on an overall mechanism are analyzed in this paper. The overall kinematic constraints are explained by introducing the restriction of motion, which is a constraint that prohibits a manipulator from moving in a certain region or direction, instantaneously. By introducing it, kinematic constraints can be embedded explicitly in the formulation of rate kinematics, and by analyzing it, constraints for a desired motion can be found. This paper derives constraints for pure translational motion in a systematic way. Necessary and sufficient conditions are suggested and several translational parallel manipulators with their kinematic features are provided.

Issue Section:
Technical Papers
Keywords:
manipulator kinematics, motion control, Jacobian matrices
Topics:
Kinematics, Manipulators
1.
Tsai, L. W., 1996 “Kinematics of a Three-DOF Platform with Three Extensible Limbs,” Recent Advances in Robot Kinematics, J. Lenarcic and V. Parenti-Castelli, eds., Kluwer Academic Publishers, pp. 401–410.
2.
Stamper, R. E., Tsai, L. W., and Walsh, G. C., 1997 “Optimization of a Three DOF Translational Platform for Well-Conditioned Workspace,” IEEE Int. Conf. on Robotics and Automation, pp. 3250–3255.
3.
Di Gregorio, R., 2001 “Kinematics of the Translational 3-URC Mechanism,” IEEE/ASME Int. Conf. on Advanced Intelligent Mechatronics, pp. 147–152.
4.
Herve´, J. M., and Sparacino, F., 1991 “Structural Synthesis of “Parallel” Robots Generating Spatial Translation,” Int. Conf. on Advanced Robotics, pp. 808–813.
5.
Frisoli, A., Checcacci, D., Salsedo, F., and Bergamasco, M., 2000 “Synthesis by Screw Algera of Translating In-Parallel Actuated Mechanisms,” Advances in Robot Kinematics, J. Lenarvcivc and M. M. Stanivsivc, eds., Kluwer Academic Publishers, pp. 433–440.
6.
Di Gregorio, R., and Parenti-Castelli, V., 1999, “Mobility Analysis of the 3-UPU Parallel Mechanism Assembled for a Pure Translational Motion,” IEEE Int. Conf. on Robotics and Automation, pp. 520–525.
7.
Lee, S., and Kim, S., 1994, “Kinematic Feature Analysis of Parallel Manipulator Systems,” IEEE Int. Conf. on Robotics and Automation, pp. 77–82.
8.
Kim
,
D.
, and
Chung
,
W. K.
,
2003
, “
Analytic Formulation of Reciprocal Screws and Its Application to Non-Redundant Robot Manipulators
,”
ASME J. Mech. Des.
,
accepted
accepted
.
9.
Lipkin
,
H.
, and
Duffy
,
J.
,
1985
, “
The Elliptic Polarity of Screws
,”
ASME J. Mech. Transm., Auton. Des.
,
108
, pp.
377
–
387
.
10.
Tsai, L. W., 1999, Robot Analysis: The Mechanics of Serial and Parallel Manipulators, John Wiley & Sons, Inc.
11.
Tsai, L. W., 1998, “Systematic Enumeration of Parallel Manipulators,” Technical Research Report, No. T.R.98–33.
12.
Kumar
,
V.
,
1992
, “
Instantaneous Kinematics of Parallel-Chain Robotic Mechanisms
,”
ASME J. Mech. Des.
,
114
, pp.
349
–
358
.
Copyright © 2003
 by ASME
You do not currently have access to this content.