1-11 of 11
Keywords: glass transition
Close
Sort by
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Eng. Mater. Technol. July 2019, 141(3): 031005.
Paper No: MATS-18-1117
Published Online: March 11, 2019
...D. Mathiesen; A. Kakumani; R. B. Dupaix Spring-back of poly(methyl methacrylate) (PMMA) at large strains, various embossing temperatures, and release temperatures below glass transition is quantified through modified unconfined recovery tests. Cooling, as well as large strains, is shown to reduce...
Journal Articles
Publisher: ASME
Article Type: Bridging Microstructure, Properties, And Processing Of Polymer-Based Advanced Materials
J. Eng. Mater. Technol. January 2012, 134(1): 010910.
Published Online: December 21, 2011
... their mechanical behavior. Depending on the amount of PVDF, either amorphous or semicrystalline blends are produced. Typically, the blends remain amorphous when their PVDF content does not exceed 40 wt. %. Blend composition influence on the values of the glass transition temperature, T g , and on its mechanical...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. October 2011, 133(4): 041007.
Published Online: October 14, 2011
... manufactured inside a woven using a silicone mold. Samples with rectangular cross-section were subjected to a predetermined amount of tensile strain and the tensile force was recorded as a function of time. Relaxation modulus was determined for different temperatures up to near the glass transition temperature...
Journal Articles
Publisher: ASME
Article Type: Multi-Physics Approaches For The Behavior Of Polymer-Based Materials
J. Eng. Mater. Technol. July 2011, 133(3): 030902.
Published Online: June 23, 2011
...A. Goel; Y. Wen; J. Hein; M. Negahban; J. A. Turner The development of anisotropy as a result of isothermal plastic deformation below the glass transition temperature is investigated for different deformation temperatures. Initially, isotropic polycarbonate was subjected to different extents...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. January 2011, 133(1): 011016.
Published Online: December 3, 2010
... with temperature and then slightly decrease or stay flat, attaining peak values around the glass transition region. The glass transition temperature (measured as the temperature at the maximum value of the loss modulus) shifted toward higher temperatures as the fly ash volume fraction increased. Additionally, we...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. July 2010, 132(3): 031016.
Published Online: June 24, 2010
...- and microparticles and were especially formulated for bonded-in timber connections, and the properties of bulk adhesives and adhesively bonded block shear specimens were evaluated. After 90 days of aging the results demonstrate critical temperature effects controlled by the glass transition temperature. The apparent...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. July 2008, 130(3): 031005.
Published Online: June 10, 2008
.... Except for slight reduction in flexural strength, up to 9.5% increase in tensile strength, stiffness, and flexural modulus are observed. Glass transition temperature is determined under oscillatory torsion and observed to increase by 4.5% by the addition of nanoclay. 12 05 2004 18 03 2008...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. October 2006, 128(4): 478–483.
Published Online: May 8, 2006
... density on the position of the glass transition and the rubbery modulus was calculated. The model was tested with a series of Novolac epoxies in which the functionality, mixing ratio, and conversion level were varied systematically. It turned out that changes in the relaxation curves due to variations...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. October 2006, 128(4): 586–594.
Published Online: April 13, 2006
... data and recovery data, perhaps due to accumulated damage during the creep cycle. Our results indicate that the nonlinear viscoelastic behavior significantly contributes to structural behavior under fire loading conditions. 20 10 2005 13 04 2006 thermoelasticity glass transition...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Eng. Mater. Technol. January 2006, 128(1): 34–40.
Published Online: June 8, 2005
... as influencing fatigue performance. glass fibre reinforced plastics curing transfer moulding laminates fatigue creep shrinkage ageing viscoelasticity glass transition The degree of cure of vinyl-ester resin composites produced by the vacuum-assisted resin transfer molding (VARTM) process has...