Discontinuously Reinforced Aluminum (DRA) Composites form unique case from the research in metal cutting point of view. Reinforcement in these materials acts as “macroscopic” and “isolated” discontinuities in the path of the tool. The mechanism of chip formation for such materials is yet to be evolved completely. In this paper, the mechanism of chip formation during machining of Al/SiCp composites based on the micro-structural analysis of chips and chip roots is presented. It was evident that the mechanism involves initiation of a gross fracture on the chip free surface and its propagation toward the tool nose. The extent of propagation of gross fracture depends upon the cutting speed and volume of reinforcement in composites. A model of deformation of the material along the shear plane is presented in terms of a ratio of length of flow-type deformation on the shear plane to the total length of shear plane. Influence of volume of reinforcement in composites and cutting speed on the ratio was verified experimentally.
Skip Nav Destination
Article navigation
July 2001
Technical Papers
Micro-Structural Analysis of Chip Formation During Orthogonal Machining of Composites
S. S. Joshi,
S. S. Joshi
Department of Mechanical Engineering, Indian Institute of Technology, Bombay, Powai, Mumbai, 400 076 India
Search for other works by this author on:
N. Ramakrishnan,
N. Ramakrishnan
Department of Mechanical Engineering, Indian Institute of Technology, Bombay, Powai, Mumbai, 400 076 India
Search for other works by this author on:
P. Ramakrishnan
P. Ramakrishnan
Department of Metallurgical Engineering, Indian Institute of Technology, Bombay, Powai, Mumbai, 400 076 India
Search for other works by this author on:
S. S. Joshi
Department of Mechanical Engineering, Indian Institute of Technology, Bombay, Powai, Mumbai, 400 076 India
N. Ramakrishnan
Department of Mechanical Engineering, Indian Institute of Technology, Bombay, Powai, Mumbai, 400 076 India
P. Ramakrishnan
Department of Metallurgical Engineering, Indian Institute of Technology, Bombay, Powai, Mumbai, 400 076 India
Contributed by the Materials Division for publication in the JOURNAL OF ENGINEERING MATERIALS AND TECHNOLOGY. Manuscript received by the Materials Division April 23, 1999; revised manuscript received November 17, 2000. Associate Editor A. M. Rajendran.
J. Eng. Mater. Technol. Jul 2001, 123(3): 315-321 (7 pages)
Published Online: November 17, 2000
Article history
Received:
April 23, 1999
Revised:
November 17, 2000
Citation
Joshi , S. S., Ramakrishnan, N., and Ramakrishnan, P. (November 17, 2000). "Micro-Structural Analysis of Chip Formation During Orthogonal Machining of Composites ." ASME. J. Eng. Mater. Technol. July 2001; 123(3): 315–321. https://doi.org/10.1115/1.1356026
Download citation file:
Get Email Alerts
Modeling Growth and Viscous Flow of Oxide on Cylindrical Silicon Surfaces Including Piezoviscous Inhibition
J. Eng. Mater. Technol (April 2025)
Thermal Conductivity of 3D-Printed Metal Using Extrusion-Based Metal Additive Manufacturing Process
J. Eng. Mater. Technol (April 2025)
Related Articles
Chaotic Phenomena Induced by the Fast Plastic Deformation of Metals During Cutting
J. Appl. Mech (March,2006)
Mechanics of Machining With Chamfered Tools
J. Manuf. Sci. Eng (November,2000)
A Study of Burr Formation Processes Using the Finite Element Method: Part II—The Influences of Exit Angle, Rake Angle, and Backup Material on Burr Formation Processes
J. Eng. Mater. Technol (April,2000)
A New Model and Analysis of Orthogonal Machining With an Edge-Radiused Tool
J. Manuf. Sci. Eng (August,2000)
Related Proceedings Papers
Related Chapters
Introduction and Definitions
Handbook on Stiffness & Damping in Mechanical Design
Understanding the Problem
Design and Application of the Worm Gear
Research on Deformation of Aerospace Thin-Walled Structure Part in NC Machining Process
International Conference on Instrumentation, Measurement, Circuits and Systems (ICIMCS 2011)