1-12 of 12
Keywords: annealing
Close
Follow your search
Access your saved searches in your account

Would you like to receive an alert when new items match your search?
Close Modal
Sort by
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Manuf. Sci. Eng. November 2022, 144(11): 114501.
Paper No: MANU-22-1061
Published Online: June 22, 2022
..., all tests use the rigid tool punch to deform the hole. The cruciform specimen with a center hole was used to make the sample, which fits in all the considered tests. Force–displacement curves were plotted and discussed. In addition, tests were also performed on annealed materials to understand...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Manuf. Sci. Eng. April 2014, 136(2): 021012.
Paper No: MANU-13-1089
Published Online: January 16, 2014
..., and punch arc region are taken into account for the analytical determination of LDR. The presented method can predict the limiting drawing ratio for redrawing with/without intermediate annealing processes. The results are compared to numerical results and experimental results reported in the literature...
Journal Articles
Publisher: ASME
Article Type: Research-Article
J. Manuf. Sci. Eng. February 2014, 136(1): 011008.
Paper No: MANU-13-1005
Published Online: November 5, 2013
... Symmetric Polarization Aberrations in a Lens by Annealing ,” Opt. Express , 12 ( 15 ), pp. 3443 – 3451 . 10.1364/OPEX.12.003443 [10] Lillie , H. R. , and Ritland , H. N. , 1954 , “ Fine Annealing of Optical Glass ,” J. Am. Ceram. Soc. , 37 ( 10 ), pp. 466 – 473 . 10.1111/j.1151...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. December 2011, 133(6): 061016.
Published Online: December 9, 2011
...-based lubricants were applied to the sheet. In conclusion, evaluated synthetic/water-based lubricants had better lubricity than petroleum-based lubricants. 01 12 2009 14 03 2011 09 12 2011 09 12 2011 annealing deep drawing finite element analysis forming processes...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. December 2011, 133(6): 061007.
Published Online: December 1, 2011
...Jingjing Li; S. Jack Hu; John E. Carsley; Theresa M. Lee; Louis G. Hector, Jr.; Sushil Mishra The effects of different prestrain levels, paths, and subsequent annealing on the postannealing mechanical properties of AA5182-O were investigated. Aluminum sheet specimens were prestrained in uniaxial...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. October 2010, 132(5): 051004.
Published Online: September 20, 2010
... and atomic force microscopy. The role of microstructure and composition in altering both the mechanical and shape memory properties of the films is discussed. 22 06 2009 01 07 2010 20 09 2010 20 09 2010 annealing atomic force microscopy metallic thin films nanoindentation...
Journal Articles
Publisher: ASME
Article Type: Research Papers
J. Manuf. Sci. Eng. June 2009, 131(3): 031001.
Published Online: April 15, 2009
... analysis. Boriding on as-received titanium articles resulted in shape distortion that hampered the subsequent polishing efforts. Hence, further articles were treated with stress-relief annealing prior to boriding, at temperatures below and above the β -transus of the substrate article. Annealing itself...
Journal Articles
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Manuf. Sci. Eng. February 2007, 129(1): 216–222.
Published Online: June 21, 2006
... that the fatigue strength of the rolled bolts are 55% higher than the machined bolts and by full annealing at 850 ° C , it reduced to the extent of machined specimen. Partial annealing of the thread rolled bolts at 680 ° C caused a reduction of fatigue strength by approximately 61% due to reduction...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. August 2006, 128(3): 683–690.
Published Online: November 17, 2005
...Anurag Jain; Allen Y. Yi The precision lens molding process is numerically modeled by incorporating the characteristic structural relaxation phenomenon of glass during the annealing stage. A review of the structural relaxation theory as explained by the Narayanaswamy model ( Narayanaswamy, 1971, J...
Journal Articles
Publisher: ASME
Article Type: Technical Briefs
J. Manuf. Sci. Eng. November 2001, 123(4): 748–753.
Published Online: September 1, 2000
...Kurt Jacobus, Mem. ASME, Graduate Research Assistant; S. G. Kapoor, Fellow ASME, Professor; R. E. DeVor, Fellow ASME, Professor Residual stress measurements from endmilling of annealed AISI 4340 have been made at multiple points within the cut geometry to investigate the effects of location...
Journal Articles
Publisher: ASME
Article Type: Technical Papers
J. Manuf. Sci. Eng. February 2000, 122(1): 20–31.
Published Online: June 1, 1999
...Kurt Jacobus, Member, ASME, Graduate Research Assistant; R. E. DeVor, Fellow, ASME, Professor; S. G. Kapoor, Fellow, ASME, Professor Controlled orthogonal and controlled oblique machining of annealed AISI 4340 have been undertaken in a design of experiments framework to investigate the machining...