This paper presents a study combining additive manufactured (AM) elements with carbon fiber-reinforced polymers (CFRP) for the autoclave curing of complex-shaped, lightweight structures. Two approaches were developed: First, structural cores were produced with AM, over-laminated with CFRP, and co-cured in the autoclave. Second, a functional hull is produced with AM, filled with a temperature- and pressure-resistant material, and over-laminated with CFRP. After curing, the filler-material is removed to obtain a hollow lightweight structure. The approaches were applied to hat stiffeners, which were modeled, fabricated, and tested in three-point bending. Results show weight savings by up to 5% compared to a foam core reference. Moreover, the AM element contributes to the mechanical performance of the hat stiffener, which is highlighted by an increase in the specific bending stiffness and the first failure load by up to 18% and 310%. Results indicate that the approaches are appropriate for composite structures with complex geometries.
Issue Section:
Design Innovation Paper
References
1.
Evans
, A. G.
, 2001
, “Lightweight Materials and Structures
,” MRS Bull.
, 26
(10
), pp. 790
–797
.2.
Davies
, J. M.
, 2001
, Lightweight Sandwich Construction
, Wiley-Blackwell
, Oxford, UK
.3.
Herrmann, A. S., Zahlen, P. C., Zuardy, I., 2005, “
Sandwich Structures Technology in Commercial Aviation
,” Sandwich Structures 7: Advancing with Sandwich Structures and Materials
, Thomsen, O., Bozhevolnaya, E., and Lyckegaard, A. eds., Springer, Dordrecht, The Netherlands.4.
Anders
, M.
, Zebrine
, D.
, Centea
, T.
, and Nutt
, S.
, 2017
, “In Situ Observations and Pressure Measurements for Autoclave Co-Cure of Honeycomb Core Sandwich Structures
,” ASME J. Manuf. Sci. Eng.
, 139
(11
), p. 111012
.5.
Kodiyalam
, S.
, Nagendra
, S.
, and DeStefano
, J.
, 1996
, “Composite Sandwich Structure Optimization With Application to Satellite Components
,” AIAA J.
, 34
(3
), pp. 614
–621
.6.
Huang
, X.
, and Xie
, Y. M.
, 2008
, “Optimal Design of Periodic Structures Using Evolutionary Topology Optimization
,” Struct. Multidiscip. Optim.
, 36
(6
), pp. 597
–606
.7.
Gibson
, L. J.
, and Ashby
, M. F.
, 1999
, Cellular Solids: Structure and Properties
, Cambridge University Press
, Cambridge, UK
.8.
Huang
, S. N.
, and Alspaugh
, D. W.
, 1974
, “Minimum Weight Sandwich Beam Design
,” AIAA J.
, 12
(12
), pp. 1617
–1618
.9.
Li
, X.
, Li
, G.
, Wang
, C. H.
, and You
, M.
, 2012
, “Optimisation of Composite Sandwich Structures Subjected to Combined Torsion and Bending Stiffness Requirements
,” Appl. Compos. Mater.
, 19
(3–4
), pp. 689
–704
.10.
Catapano
, A.
, and Montemurro
, M.
, 2014
, “A Multi-Scale Approach for the Optimum Design of Sandwich Plates With Honeycomb Core—Part I: Homogenization of Core Properties
,” Compos. Struct.
, 118
, pp. 664
–676
.11.
Catapano
, A.
, and Montemurro
, M.
, 2014
, “A Multi-Scale Approach for the Optimum Design of Sandwich Plates With Honeycomb Core—Part II: The Optimization Strategy
,” Comp. Struct.
, 118
, pp. 677
–690
.12.
Krieglsteiner
, J.
, Horst
, P.
, and Schmidt
, C.
, 2014
, “Characterization of Fiber-Reinforced Stiffener Profiles for Aircraft Fuselage Preliminary Structural Design
,” 16th European Conference on Composite Materials
(ECCM
), Seville, Spain, June 22–26, pp. 1–8.13.
Tosh
, M. W.
, and Kelly
, D. W.
, 2001
, “Fibre Steering for a Composite C-Beam
,” Comp. Struct.
, 53
(2
), pp. 133
–141
.14.
Alinia
, M. M.
, and Moosavi
, S. H.
, 2008
, “A Parametric Study on the Longitudinal Stiffeners of Web Panels
,” Thin-Walled Struct.
, 46
(11
), pp. 1212
–1223
15.
Kaufmann
, M.
, Zenkert
, D.
, and Mattei
, C.
, 2008, “Cost Optimization of Composite Aircraft Structures Including Variable Laminate Qualities
,” Comp. Sci. Technol.
, 68
(13
), pp. 2748
–2754
.16.
Mukhopadhyay
, M.
, 2004
, Mechanics of Composite Materials and Structures
, University Press
, Hyderguda
, India.17.
Zenkert
, D.
, 1995
, An Introduction to Sandwich Construction
, Engineering Materials Advisory Services
, London
.18.
Gutowski
, T. G.
, 1997
, Advanced Composites Manufacturing
, Wiley
, Cambridge, UK
.19.
Advanced Ceramics Manufacturing, 2017, “
Advanced Ceramics Manufacturing
,” Tucson, AZ, accessed June 20, 2017, http://www.acmtucson.com20.
Black
, S.
, 2015
, “3D Printing Moves Into Tooling Components
,” CompositesWorld, Cincinnati, OH, accessed June 15, 2017, https://www.compositesworld.com/articles/3d-printing-moves-into-tooling-components21.
ASTM
, 2012
, “Standard Terminology for Additive Manufacturing Technologies
,” West Conshohocken, PA, Standard No. ASTM F2792-12a
.22.
Stratasys
, 2017, “Introduction to Additive Manufacturing for Composites
,” Stratasys, Eden Prairie, MN, accessed June 20, 2017, http://www.stratasys.com/de/campaign/ebook/additive-manufacturing-for-composites23.
Li
, H.
, Taylor
, G.
, Bheemreddy
, V.
, Iyibilgin
, O.
, Leu
, M.
, and Chandrashekhara
, K.
, 2015
, “Modeling and Characterization of Fused Deposition Modeling Tooling for Vacuum Assisted Resin Transfer Molding Process
,” Addit. Manuf.
, 7
, pp. 64
–72
.24.
Lušic
, M.
, Schneider
, K.
, and Hornfeck
, R.
, 2016
, “A Case Study on the Capability of Rapid Tooling Thermoplastic Laminating Moulds for Manufacturing of CFRP Components in Autoclaves
,” Procedia CIRP
, 50
, pp. 390
–395
.25.
Prüß
, H.
, and Vietor
, T.
, 2015
, “Design for Fiber-Reinforced Additive Manufacturing
,” ASME J. Mech. Des.
, 137
(11
), p. 111409
.26.
Hassen
, A.
, Lindahl
, J.
, Chen
, J.
, Post
, B.
, Love
, L.
, and Kunc
, V.
, 2016
, “Additive Manufacturing of Composite Tooling Using High Temperature Thermoplastic Materials
,” SAMPE Conference Proceedings
, Long Beach, CA, May 23–26, pp. 2648
–2658
.27.
Stratasys
, 2017, “Sacrificial Tooling and Mandrels Composite Part Fabrication—Design Guide
,” Stratasys, Eden Prairie, MN, accessed June 21, 2017, http://www.stratasys.com/solutions/additive-manufacturing/tooling/composite-tooling28.
Türk
, D.-A.
, Triebe
, L.
, and Meboldt
, M.
, 2016
, “Combining Additive Manufacturing With Advanced Composites for Highly Integrated Robotic Structures
,” Procedia CIRP
, 50
, pp. 402
–407
.29.
Nygaard
, J. V.
, and Lyckegaard
, A.
, 2007
, “Sandwich Beam With a Periodical and Graded Core Manufactured Using Rapid Prototyping
,” J. Sandwich Struct. Mater.
, 9
(4
), pp. 365
–376
.30.
Williams
, R. R.
, Howard
, W. E.
, and Martin
, S. M.
, 2011
, “Composite Sandwich Structures With Rapid Prototyped Cores
,” Rapid Prototyping J.
, 17
(2
), pp. 92
–97
.31.
Li
, T.
, and Wang
, L.
, 2017
, “Bending Behavior of Sandwich Composite Structures With Tunable 3D-Printed Core Materials
,” Compos. Struct.
, 175
, pp. 46
–57
.32.
Morena
, J. J.
, 2011
, Mold Fabrications
, Wiley Encyclopedia of Composites
, Hoboken, NJ.33.
Bitzer
, T.
, 2012
, Honeycomb Technology: Materials, Design, Manufacturing, Applications and Testing
, Springer Science & Business Media
, Dordrecht, The Netherlands.34.
Stankunas
, T.
, Mazenko
, D.
, and Jensen
, G.
, 1989
, “Cocure Investigation of a Honeycomb Reinforced Spacecraft Structure
,” 21st International SAMPE Technical Conference
, Atlantic City, NJ, pp. 176
–188
.35.
Campbell
, F. C.
, Jr., 2003
, Manufacturing Processes for Advanced Composites
, Elsevier
, Oxford, UK.36.
ROHACELL
, 2017
, “Rohacell IG-F Datasheet
,” Essen, Germany, accessed May 8, 2017, http://www.rohacell.com/sites/lists/RE/DocumentsHP/ROHACELL%20IG_IG-F%20Product%20Information.pdf37.
Sigmund
, O.
, Aage
, N.
, and Andreassen
, E.
, 2016
, “On the (Non-)Optimality of Michell Structures
,” Struct. Multidiscip. Optim.
, 54
(2
), pp. 361
–373
.38.
Kussmaul
, R.
, Zogg
, M.
, and Ermanni
, P.
, 2018
, “An Optimality Criteria-Based Algorithm for Efficient Design Optimization of Laminated Composites Using Concurrent Resizing and Scaling
,” Struct. Multidiscip. Optim.
(epub).39.
Sriapai
, T.
, Walsri
, C.
, and Fuenkajorn
, K.
, 2012
, “Effect of Temperature on Compressive and Tensile Strength of Salt
,” ScienceAsia
, 38
(2
), pp. 166
–174
.40.
3D Systems
, 2017
, “DuraForm HST Composite Datasheet
,” 3D Systems, Rock Hill, SC, accessed May 8, 2017, https://www.3dsystems.com/materials/duraform-hst-composite/tech-specs41.
Schmid
, M.
, 2015
, Selektives Lasersintern (SLS) Mit Kunststoffen
, Hanser
, Munich, Germany
.42.
Türk
, D. A.
, Brenni
, F.
, Zogg
, M.
, and Meboldt
, M.
, 2017
, “Mechanical Characterization of 3D Printed Polymers for Fiber Reinforced Polymers Processing
,” Mater. Des.
, 118
, pp. 256
–265
.43.
Gere
, J. M.
, and Goodno
, B. J.
, 2013
, Mechanics of Materials
, Cengage Learning
, Stamford, CT
.44.
Dewulf
, W.
, Pavan
, M.
, Craeghs
, T.
, and Kruth
, J.-P.
, 2016
, “Using X-Ray Computed Tomography to Improve the Porosity Level of Polyamide-12 Laser Sintered Parts
,” CIRP Ann.
, 65
(1
), pp. 205
–208
.45.
Shaw
, B.
, and Dirven
, S.
, 2016
, “Investigation of Porosity and Mechanical Properties of Nylon SLS Structures
,” 23rd International Conference on Mechatronics and Machine Vision in Practice
(M2VIP
), Nanjing, China, Nov. 28–30, pp. 1–6.46.
Ho
, H. C. H.
, Gibson
, I.
, and Cheung
, W. L.
, 1999
, “Effects of Energy Density on Morphology and Properties of Selective Laser Sintered Polycarbonate
,” J. Mater. Process. Technol.
, 89–90
, pp. 204
–210
.47.
Rahman
, K. M.
, Hu
, Z.
, and Letcher
, T.
, 2017
, “In-Plane Stiffness of Additively Manufactured Hierarchical Honeycomb Metamaterials With Defects
,” ASME J. Manuf. Sci. Eng.
, 140
(1
), p. 011007
.48.
Beyer
, D.
, and Figueroa
, D.
, 2016
, “Design and Analysis of Lattice for Additive Manufacturing
,” ASME J. Manuf. Sci. Eng.
, 138
(12
), p. 121015
..49.
Schmidt
, M.
, Pohle
, D.
, and Rechtenwald
, T.
, 2007
, “Selective Laser Sintering of PEEK
,” CIRP Ann. Manuf. Technol.
, 56
(1
), pp. 205
–208
.50.
Fish
, S.
, Booth
, J. C.
, Kubiak
, S. T.
, Wroe
, W. W.
, Bryant
, A. D.
, Moser
, D. R.
, and Beaman
, J. J.
, 2015
, “Design and Subsystem Development of a High Temperature Selective Laser Sintering Machine for Enhanced Process Monitoring and Control
,” Addit. Manuf.
, 5
, pp. 60
–67
.Copyright © 2018 by ASME
You do not currently have access to this content.
