A model to predict tool failure due to chipping in machining via the microstructure-level finite element cutting process simulation is presented and applied to a wide variety of WC-Co tool materials. The methodology includes the creation of arbitrary microstructures comprised of WC and Co phases to simulate various grades of WC-Co alloys. Equivalent stress, strain, and strain energy are then obtained via orthogonal microstructure-level finite element machining simulations. A model was developed to predict the occurrence of tool failure based on the mixed mode fracture criterion. Turning experiments were conducted to validate the model and the results showed that the model predictions agree well with the observations from the experiments. The model was then employed to study the effects of microstructural parameters and feedrate on chipping and failure.
Issue Section:
Technical Papers
1.
Loladze
, T. N.
, 1975, “Nature of Brittle Failure of Cutting Tool
,” CIRP Ann.
0007-8506, 24
(1
), pp. 13
–16
.2.
Uehara
, K.
, and Kanda
, Y.
, 1977, “On the Chipping Phenomena of Carbide Cutting Tools
,” CIRP Ann.
0007-8506, 25
(1
), pp. 11
–16
.3.
Williams
, W. S.
, 1964, “Influence of Temperature, Strain Rate, Surface Condition, and Composition on the Plasticity of Transition-Metal Carbide Crystals
,” J. Appl. Phys.
0021-8979, 35
(4
), pp. 1329
–1338
.4.
Lee
, I. C.
, and Sakuma
, T.
, 1997, “High-Temperature Tensile Ductility in WC-Co Cemented Carbides
,” Metall. Mater. Trans. A
1073-5623, 28A
, pp. 1843
–1847
.5.
Pandey
, P. C.
, Bhatia
, S. M.
, and Shan
, H. S.
, 1979, “Thermomechanical Failure of Cemented Carbide Tools in Intermittent Cutting
,” CIRP Ann.
0007-8506, 28
(1
), pp. 13
–17
.6.
Chandrasekaran
, H.
, 1985, “Thermal Fatigue Studies on Tool Carbides and Its Relevance of Milling Cutters
,” CIRP Ann.
0007-8506, 34
(1
), pp. 125
–128
.7.
Liu
, B.
, Zhang
, Y.
, and Ouyang
, S.
, 2000, “Study on the Relation between Structural Parameters and Fracture Strength of WC-Co Cemented Carbides
,” Mater. Chem. Phys.
0254-0584, 62
, pp. 35
–43
.8.
Gurland
, J.
, 1984, “Application of Quantitative Microscopy to Cemented Carbides
,” ASTM STP, 839, ASTM Philadelphia, PA, pp. 65
–84
.9.
Tlusty
, J.
, and Masood
, Z.
, 1978, “Chipping and Breakage of Carbide Tools
,” ASME J. Eng. Ind.
0022-0817, 100
, pp. 403
–412
.10.
Sampath
, W. S.
, Lee
, Y. M.
, and Shaw
, M. C.
, 1984, “Tool Fracture Probability under Steady State Cutting Conditions
,” ASME J. Eng. Ind.
0022-0817, 106
, pp. 161
–167
.11.
Wu
, H.
, and Mayer
, J. E.
, Jr., 1979, “An Analysis of Thermal Cracking of Carbide Tools in Intermittent Cutting
,” ASME J. Eng. Ind.
0022-0817, 101
, pp. 159
–164
.12.
Hirao
, M.
, Murata
, R.
, and Takeyama
, H.
, 1977, “Microscopic Stress Analysis of Sintered Carbide
,” CIRP Ann.
0007-8506, 25
(1
), pp. 27
–31
.13.
Fischmeister
, H. F.
, Schmauder
, S.
, and Sigl
, L. S.
, 1988, “Finite Element Modelling of Crack Propagation in WC-Co Hard Metals
,” Mater. Sci. Eng., A
0921-5093, 105/106
, pp. 305
–311
.14.
Sigl
, L. S.
, and Fischmeister
, H. F.
, 1988, “On the Fracture Toughness of Cemented Carbides
,” Acta Metall.
0001-6160, 36
(4
), pp. 887
–897
.15.
Chuzhoy
, L.
, DeVor
, R. E.
, Kapoor
, S. G.
, and Bammann
, D. J.
, 2002, “Microstructure-Level Modeling of Ductile Iron Machining
,” ASME J. Manuf. Sci. Eng.
1087-1357, 124
, pp. 162
–169
.16.
Park
, S.
, Kapoor
, S. G.
, and DeVor
, R. E.
, 2004, “Mechanistic Cutting Process Calibration Via Microstructure-Level Finite Element Simulation Model
,” ASME J. Manuf. Sci. Eng.
1087-1357, 126
(4
), pp. 706
–709
.17.
Betteridge
, W.
, 1979, “The Properties of Metallic Cobalt
,” Prog. Mater. Sci.
0079-6425, 24
(2
), pp. 51
–142
.18.
Engineering Properties of Selected Ceramic Materials
, 1966, American Ceramic Society, J. F.
Lynch
, C. G.
Ruderer
, and W. H.
Duckworth
, eds., American Chemical Society
.19.
Munro
, R. G.
, 1997, “Material Properties of a Sintered α-SiC
,” J. Phys. Chem. Ref. Data
0047-2689, 26
(5
), pp. 1195
–1203
.20.
Ng
, E.
, El-Wardany
, T. I.
, Cumitrescu
, M.
, and Elbestawi
, M.
, 2002, “Physics Based Simulation of High Speed Machining
,” in Proceedings of the 5th CIRP International Workshop on Modeling of Machining Operations
, May 2002, Purdue University
, West Lafayette, IN
, pp. 1
–19
.21.
Özel
, T.
, and Altan
, T.
, 1998, “Modeling of High Speed Machining Processes for Predicting Tool Forces, Stresses and Temperatures Using FEM Simulations
,” in Proceedings of the CIRP International Workshop on Modeling of Machining Operations
, May 19, 1998, Atlanta, GA, pp. 225
–234
.22.
Warren
, R.
, 1978, “Measurement of the Fracture Properties of Brittle Solids by Hertzian Indentation
,” Acta Metall.
0001-6160, 26
, pp. 1756
–1769
.23.
Griffith
, A. A.
, 1921, “The Phenomena of Rupture and Flow in Solids
,” Philos. Trans. R. Soc. London, Ser. A
0962-8428, 221
, pp. 163
–198
.24.
Dixon
, G.
, and Wright
, N.
, 1989, “Creep Deformation of WC-Co Alloys
,” Int. J. Refract. Met. Hard Mater.
0263-4368, 8
, pp. 55
–60
.25.
Rice
, J. R.
, and Tracey
, D. M.
, 1969, “On the Ductile Enlargement of Voids in Triaxial Stress Fields
,” J. Mech. Phys. Solids
0022-5096, 17
(3
), pp. 201
–217
.26.
Marini
, B.
, Mudry
, F.
, and Pineau
, A.
, 1985, “Experimental Study of Cavity Growth in Ductile Rupture
,” Eng. Fract. Mech.
0013-7944, 22
(6
), pp. 989
–996
.27.
Santhanam
, A. T.
, and Tierney
, P.
, 1989, “Cemented Carbides,” Metals Handbook
, 9th ed., ASM International
, Vol. 16
, pp. 71
–89
.28.
Warren
, R.
, 1976, “Determination of the Interfacial Energy Fatio in Two-Phase Systems by Measurement of Interphase Contact
,” Metallography
0026-0800, 9
, pp. 183
–191
.29.
Chermant
, J. L.
, and Osterstock
, F.
, 1976, “Fracture Toughness and Fracture of WC-Co Composites
,” J. Mater. Sci.
0022-2461, 11
, 1939
–1951
.30.
Suresh
, S.
, Shih
, C. F.
, Morrone
, A.
, and O’Dowd
, N. P.
, 1990, “Mixed-Mode Fracture Toughness of Ceramic Materials
,” J. Am. Ceram. Soc.
0002-7820, 73
(5
), pp. 1257
–1267
.31.
Eftis
, J.
, and Subramonia
, N.
, 1978, “The Inclined Crack under Biaxial Load
,” Eng. Fract. Mech.
0013-7944, 10
, pp. 43
–67
.32.
Torres
, Y.
, Anglada
, M.
, and Llanes
, L.
, 2001, “Fatigue Mechanics of WC-Co Cemented Carbides
,” Int. J. Refract. Met. Hard Mater.
0263-4368, 19
, pp. 341
–348
.33.
Exner
, H. E.
, Sigl
, L.
, Fripan
, M.
, and Pompe
, O.
, 2001, “Fractography of Critical and Subcritical Cracks in Hard Materials
,” Int. J. Refract. Met. Hard Mater.
0263-4368, 19
, pp. 329
–334
.34.
Godse
, R.
, and Gurland
, J.
, 1988, “Applicability of the Critical Strain Fracture Criterion to WC-Co Hard Metals
,” Mater. Sci. Eng., A
0921-5093, 105/106
, pp. 331
–336
.Copyright © 2006
by American Society of Mechanical Engineers
You do not currently have access to this content.
