This paper discusses a control system for microwave processing of materials. Microwave joining of ceramics and drying of timber are currently industry practices while microwave joining of engineering plastics and curing of epoxy adhesives are still being researched. In this study, all materials are processed in rectangular sections of waveguide fed by a magnetron with a maximum output power of 2 kW operating at 2.45 GHz. The most significant problems encountered when processing these materials are: (i) maintaining proper tuning to ensure maximum power transfer, (ii) thermal runaway, where the heating rate proceeds so rapidly that the material burns within a few seconds, and (iii) hot spot development, where localized regions heat up at a faster rate than adjacent regions. A computerized automated control system has been developed to alleviate these processing problems and has been successfully employed in joining a range of ceramics and engineering plastics, curing epoxy adhesives and drying wood. Results of preliminary tests obtained using the developed prototype are presented. [S1087-1357(00)71701-1]

Issue Section:
Technical Papers
Keywords:
microwave heating, control systems, ceramics, computerised control, plastics, magnetrons
Topics:
Ceramics, Control systems, Heating, Joining, Microwaves, Standing waves, Temperature, Waveguides, Materials processing, Hardening (Curing), Wood products, Process control, Adhesives
1.
Metaxas, A. C., and Meredith, R. J., 1983, Industrial Microwave Heating, Peter Peregrinus Ltd, London, Book.
2.
Soon, C. T., Nov. 1996, “Microwave Joining of Ceramics,” Manufacturing Project Report, Queensland University of Technology, Brisbane, Project Report.
3.
Fukushima, H., Yamanaka, T., and Matsui, M., 1990, “Microwave Heating of Ceramics and its Application to Joining,” J. Mater. Res., 5, No. 2.
4.
Do Rego, D., Nov. 1991, Continuous Joining of Flat PVC Using Focussed Microwave Energy, BE (Mechanical) thesis, University of Wollongong.
5.
Glutz, P., Nov. 1990, Microwave Joining of Plastics, BE (Mechanical) thesis, University of Wollongong.
6.
Liu, F., Turner, I., Siores, E., and Groombridge, P., 1996, “A Numerical and Experimental Investigation of the Microwave Heating of Polymer Materials Inside a Ridge Waveguide,” J. Microwave Power Electromagn. Energy, 31, No. 2.
7.
Siores, E., and Groombridge, P., 1996, “Microwave Guide Design and Temperature Control for Joining Thermoplastics,” Asian Pacific Welding Congress, Conference, Auckland, N.Z.
8.
Bond
,
G.
,
Boyes
,
R. B.
,
Pollington
,
S. D.
, and
Whan
,
D. A.
,
1991
, “
Measurement of Temperature During Microwave Heating
,”
Meas. Sci. Technol.
,
2
, pp.
571
–
572
.
9.
Bowman, R. R., 1976, “A Probe for Measuring Temperature in Radio Frequency Heated Material,” Transactions on Microwave Theory and Techniques.
10.
Buchta, R., Zhang, S. L., and Sigurd, D., 1993, “Temperature Control During Chemical Vapor Deposition of Polycrystalline Silicon with Substrate Heating by Microwaves,” Appl. Phys. Lett., 62, No. 24.
11.
Katzir, B. F., Asfour, Y., Zur, A., and Valery, C. R., 1988, “Infra Red Fibre Optics for Thermometry in Microwave,” Appl. Phys. Lett., 53, No. 19.
12.
Zur, A., and Katzir, A., 1987, “Fibres for Low Temperature Radiometric Measurements,” Appl. Opt., 26, No. 7.
13.
Kaufmann, W. J., III, 1985, Universe, W. H. Freeman and Company, Book, New York, pp. 317–318.
14.
Brydson, J. A., 1989, Plastics Materials, Butterworth Heinemann, Oxford.
15.
Yarlagadda, P. K. D. V., Ahmed, A., Soon, S. T., and Siores, E., 1997, “Microwave Welding of Alumina Ceramic Using a Ridge Waveguide,” Microwave Theory and Applications in Materials Processing, Ceramic Transactions, Vol. 80.
16.
National Materials Advisory Board on Engineering Technical Systems, 1991, “Microwave Processing of Materials,” National Research Council, Washington D.C.
17.
Peterson, E. R., Oct. 1989, “Modelling Using Dielectric Properties of Select Packaging Polymers,” Dow Chemical USA, Report, pp. 1-2-1 to 1-2-10.
18.
Groombridge, P., Oloyede, A., and Siores, E., 1997, “Process Control in Microwave Joining of Materials,” Australasian Conference on Technology for Manufacturing, Palmerston North, New Zealand.
Copyright © 2000
 by ASME
You do not currently have access to this content.