This study applies the lattice Boltzmann method (LBM) to simulate incompressible steady low Reynolds number backward-facing step flows. In order to restrict the simulations to two-dimensional flows, the investigated Reynolds number range is limited to a maximum value of Re=200. The field synergy principle is applied to demonstrate that the increased interruption within the fluid caused by the introduction of two inclined plates reduces the intersection angle between the velocity vector and the temperature gradient. The present results obtained for the velocity and temperature fields are found to be in good agreement with the published experimental and numerical results. Furthermore, the numerical results confirm the relationship between the velocity and temperature gradient predicted by the field synergy principle.
Skip Nav Destination
e-mail: ckchen@mail.ncku.edu.tw
Article navigation
November 2006
This article was originally published in
Journal of Heat Transfer
Research Papers
Lattice Boltzmann Method Simulation of Backward-Facing Step Flow With Double Plates Aligned at Angle to Flow Direction
Chao-Kuang Chen,
Chao-Kuang Chen
Department of Mechanical Engineering,
e-mail: ckchen@mail.ncku.edu.tw
National Cheng Kung University
, Tainan, 70101, Taiwan
Search for other works by this author on:
Tzu-Shuang Yen,
Tzu-Shuang Yen
Department of Mechanical Engineering,
National Cheng Kung University
, Tainan, 70101, Taiwan
Search for other works by this author on:
Yue-Tzu Yang
Yue-Tzu Yang
Department of Mechanical Engineering,
National Cheng Kung University
, Tainan, 70101, Taiwan
Search for other works by this author on:
Chao-Kuang Chen
Department of Mechanical Engineering,
National Cheng Kung University
, Tainan, 70101, Taiwane-mail: ckchen@mail.ncku.edu.tw
Tzu-Shuang Yen
Department of Mechanical Engineering,
National Cheng Kung University
, Tainan, 70101, Taiwan
Yue-Tzu Yang
Department of Mechanical Engineering,
National Cheng Kung University
, Tainan, 70101, TaiwanJ. Heat Transfer. Nov 2006, 128(11): 1176-1184 (9 pages)
Published Online: March 14, 2006
Article history
Received:
September 19, 2005
Revised:
March 14, 2006
Citation
Chen, C., Yen, T., and Yang, Y. (March 14, 2006). "Lattice Boltzmann Method Simulation of Backward-Facing Step Flow With Double Plates Aligned at Angle to Flow Direction." ASME. J. Heat Transfer. November 2006; 128(11): 1176–1184. https://doi.org/10.1115/1.2352786
Download citation file:
Get Email Alerts
Cited By
Sensitivity of Heat Transfer to the Cross Section Geometry of Cylinders
J. Heat Mass Transfer (April 2025)
Entropic Analysis of the Maximum Output Power of Thermoradiative Cells
J. Heat Mass Transfer (May 2025)
Effects of Solid-to-Fluid Conductivity Ratio on Thermal Convection in Fluid-Saturated Porous Media at Low Darcy Number
J. Heat Mass Transfer (May 2025)
Related Articles
The Nonlinear Increase of Nusselt Number With Friction Factor in Fully Developed Laminar Duct Flow
J. Heat Transfer (October,2004)
Optimization of Fin Performance in a Laminar Channel Flow Through Dimpled Surfaces
J. Heat Transfer (February,2009)
Similarity Solution for Marangoni Convection Over a Flat Surface
J. Heat Transfer (June,2002)
Related Proceedings Papers
Related Chapters
Extended Surfaces
Thermal Management of Microelectronic Equipment
Extended Surfaces
Thermal Management of Microelectronic Equipment, Second Edition
The Design and Implement of Remote Inclinometer for Power Towers Based on MXA2500G/GSM
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3