The results of a recently completed experimental and analytical study showed that the capillary limit of a helically-grooved heat pipe (HGHP) was increased significantly when the transverse body force field was increased. This was due to the geometry of the helical groove wick structure. The objective of the present research was to experimentally determine the performance of revolving helically-grooved heat pipes when the working fluid inventory was varied. This report describes the measurement of the geometry of the heat pipe wick structure and the construction and testing of a heat pipe filling station. In addition, an extensive analysis of the uncertainty involved in the filling procedure and working fluid inventory has been outlined. Experimental measurements include the maximum heat transport, thermal resistance and evaporative heat transfer coefficient of the revolving helically grooved heat pipe for radial accelerations of |a⃗r|=0.0, 2.0, 4.0, 6.0, 8.0, and 10.0-g and working fluid fills of G=0.5, 1.0, and 1.5. An existing capillary limit model was updated and comparisons were made to the present experimental data.

Issue Section:
Radiative Transfer
Keywords:
heat pipes, rotational flow, pipe flow, channel flow, Experimental, Heat Transfer, Heat Pipes, Porous Media, Two-Phase
Topics:
Fluids, Heat pipes, Heat
1.
Klasing
,
K.
,
Thomas
,
S.
, and
Yerkes
,
K.
,
1999
, “
Prediction of the Operating Limits of Revolving Helically Grooved Heat Pipes
,”
ASME J. Heat Transfer
,
121
, pp.
213
–
217
.
2.
Thomas
,
S.
,
Klasing
,
K.
, and
Yerkes
,
K.
,
1998
, “
The Effects of Transverse Acceleration Induced Body Forces on the Capillary Limit of Helically-Grooved Heat Pipes
,”
ASME J. Heat Transfer
,
120
, pp.
441
–
451
.
3.
Brennan, P., Kroliczek, E., Jen, H., and McIntosh, R., 1977, “Axially Grooved Heat Pipes,” AIAA 12th Thermophysics Conf., Paper No. 77-747.
4.
Vasiliev, L., Grakovich, L., and Khrustalev, D., 1981, “Low-Temperature Axially Grooved Heat Pipes,” Proc. 4th Int. Heat Pipe Conf., London, pp. 337–348.
5.
Faghri, A., 1995, Heat Pipe Science and Technology, Taylor and Francis, Washington, D.C.
6.
Castle, R., 1999, “The Effect of Working Fluid Inventory on the Performance of Revolving Helically Grooved Heat Pipes,” Masters thesis, Wright State University, Dayton, OH.
7.
Miller, R., 1989, Flow Measurement Engineering Handbook, 2nd ed., McGraw-Hill, New York.
8.
Peterson, G., 1994, An Introduction to Heat Pipes: Modeling, Testing, and Applications, Wiley, New York.
9.
Lide, D., and Kehiaian, H., 1994, CRC Handbook of Thermophysical and Thermochemical Data, CRC Press, Boca Raton, FL.
10.
Carey, V., 1992, Liquid-Vapor Phase-Change Phenomena, Hemisphere, Washington, D.C.
11.
Schlunder, E., 1983, Heat Exchanger Design Handbook, Hemisphere, Washington, D.C.
12.
Ivanovskii, M., Sorokin, V., and Yagodkin, I., 1982, The Physical Principles of Heat Pipes, Clarendon, Oxford.
13.
Vargaftik, N., 1975, Handbook of Physical Properties of Liquids and Gases, Hemisphere, Washington, D.C.
14.
Timmermans, J., 1950, Physico-Chemical Constants of Pure Organic Compounds, Elsevier, New York.
15.
TRC, 1983, TRC Thermodynamic Tables—Non-Hydrocarbons, Thermodynamic Research Center: The Texas A & M University System, College Station, TX (loose-leaf data sheets).
16.
Dunn, P., and Reay, D., 1978, Heat Pipes, Pergamon, Oxford.
17.
ASHRAE, 1977, Handbook of Fundamentals, American Society of Heating, Refrigerating and Air-Conditioning Engineers, Inc., Atlanta, GA.
Copyright © 2001
 by ASME
You do not currently have access to this content.