Experiments on heat transfer augmentation in a rectangular cross-section water channel are reported. The channel geometry is designed to excite normally damped Tollmien-Schlichting modes in order to enhance mixing. In this experiment, a hydrodynamically fully developed flow encounters a test section where one channel boundary is a series of periodic, saw-tooth, transverse grooves. Free shear layers span the groove openings, separating the main channel flow from the recirculating vortices contained within each cavity. The periodicity length of the grooves is equal to one-half of the expected wavelength of the most unstable mode. The remaining channel walls are flat, and the channel has an aspect ratio of 10:1. Experiments are performed over the Reynolds number range of 300 to 15,000. Streakline flow visualization shows that the flow is steady at the entrance, but becomes oscillatory downstream of an onset location. This location moves upstream with increasing Reynolds numbers. Initially formed traveling waves are two dimensional with a wavelength equal to the predicted most unstable Tollmien-Schlichting mode. Waves become three dimensional with increasing Reynolds number and distance from onset. Some evidence of wave motion persists into the turbulent flow regime. Heat transfer measurements along the smooth channel boundary opposite the grooved wall show augmentation (65 percent) over the equivalent flat channel in the Reynolds number range 1200 to 4800. The degree of enhancement obtained is shown to depend on the channel Reynolds number, and increases with the distance from the onset location.
Skip Nav Destination
Article navigation
Research Papers
Heat Transfer Augmentation Through Wall-Shape-Induced Flow Destabilization
M. Greiner,
M. Greiner
Mechanical Engineering Department, University of Nevada, Reno, Reno, NV 89557
Search for other works by this author on:
R.-F. Chen,
R.-F. Chen
Mechanical Engineering Department, University of Nevada, Reno, Reno, NV 89557
Search for other works by this author on:
R. A. Wirtz
R. A. Wirtz
Mechanical Engineering Department, University of Nevada, Reno, Reno, NV 89557
Search for other works by this author on:
M. Greiner
Mechanical Engineering Department, University of Nevada, Reno, Reno, NV 89557
R.-F. Chen
Mechanical Engineering Department, University of Nevada, Reno, Reno, NV 89557
R. A. Wirtz
Mechanical Engineering Department, University of Nevada, Reno, Reno, NV 89557
J. Heat Transfer. May 1990, 112(2): 336-341 (6 pages)
Published Online: May 1, 1990
Article history
Received:
January 23, 1989
Revised:
August 5, 1989
Online:
May 23, 2008
Citation
Greiner, M., Chen, R., and Wirtz, R. A. (May 1, 1990). "Heat Transfer Augmentation Through Wall-Shape-Induced Flow Destabilization." ASME. J. Heat Transfer. May 1990; 112(2): 336–341. https://doi.org/10.1115/1.2910382
Download citation file:
Get Email Alerts
Cited By
On Prof. Roop Mahajan's 80th Birthday
J. Heat Mass Transfer
Thermal Hydraulic Performance and Characteristics of a Microchannel Heat Exchanger: Experimental and Numerical Investigations
J. Heat Mass Transfer (February 2025)
Related Articles
Estimation of the Onset of Longitudinal Vortices in a Laminar Boundary Layer Heated From Below
J. Heat Transfer (November,1995)
Numerical Investigation of Flow Field and Heat Transfer in Cross-Corrugated Ducts
J. Heat Transfer (May,1999)
Related Proceedings Papers
Related Chapters
Cavitating Structures at Inception in Turbulent Shear Flow
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Hydraulic Resistance
Heat Transfer & Hydraulic Resistance at Supercritical Pressures in Power Engineering Applications
Heat Transfer Enhancement by Using Nanofluids in Laminar Forced Convection Flows Considering Variable Properties
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)