Hole-pattern or honeycomb seals have been commonly used for many years in the Oil & Gas industry as damper seals for turbomachinery. The main motivation has been to introduce additional damping to improve the shaft rotordynamic stability operating under high-pressure conditions. Experience has shown that the dynamic and even static characteristics of those seals are very sensitive to the operating clearance profile as well as the installation tolerances. Rotordynamic stability is related not only to the seal effective damping but to the effective stiffness as well. In fact, for this kind of seal, the effective stiffness can be high enough to alter the rotor system's natural frequency. The seal stiffness is strictly related to the tapering contour: if the clearance profile changes from divergent to convergent, the effective stiffness may change from a strong negative to a strong positive magnitude, thus avoiding the rotor natural frequency drop as it is detrimental for the stability. Unfortunately, the effective damping is reduced at the same time but this effect can be mitigated using proper devices to keep the preswirl low or even negative (e.g., swirl brakes and shunt holes). This paper presents the results from an extended test campaign performed in a high-speed rotor test rig equipped with active magnetic bearings (AMBs) working under high pressure (14 krpm, 200 bar gas inlet pressure), with the aim to validate the rotordynamic characteristics of a negative preswirl, convergent honeycomb seal and demonstrate its ability to effectively act as a gas bearing as well as a seal. The test plan included variations of inlet pressure, differential pressure (given the same inlet pressure), as well as rotational speed in order to fully validate the seal behavior. This kind of test was performed in a “dynamic mode” that is to say exciting the spinning test rotor through a pair of AMBs along linear orbits. Additionally, the impact of the seal to rotor static eccentricity and the seal to rotor angular misalignment were both experimentally investigated and compared to relevant computational fluid dynamics (CFD) simulations. This kind of test was performed in a “static mode,” that is to say imposing through the AMBs the required eccentricity/angular misalignment and then measuring the forces needed to keep the rotor in the original position. Dynamic mode test was also performed in order to check the impact of the seal static eccentricity on its dynamic behavior. Finally, the test results were compared with predictions from a state of the art bulk-flow code in order to check the predictability level for future design applications.
Skip Nav Destination
Article navigation
Research-Article
Rotordynamic Computational and Experimental Characterization of a Convergent Honeycomb Seal Tested With Negative Preswirl, High Pressure With Static Eccentricity and Angular Misalignment
Harald Underbakke
Harald Underbakke
Search for other works by this author on:
Giuseppe Vannini
Carlo Mazzali
Harald Underbakke
Contributed by the Structures and Dynamics Committee of ASME for publication in the JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Manuscript received June 20, 2016; final manuscript received August 31, 2016; published online December 1, 2016. Editor: David Wisler.
J. Eng. Gas Turbines Power. May 2017, 139(5): 052502 (10 pages)
Published Online: December 1, 2016
Article history
Received:
June 20, 2016
Revised:
August 31, 2016
Citation
Vannini, G., Mazzali, C., and Underbakke, H. (December 1, 2016). "Rotordynamic Computational and Experimental Characterization of a Convergent Honeycomb Seal Tested With Negative Preswirl, High Pressure With Static Eccentricity and Angular Misalignment." ASME. J. Eng. Gas Turbines Power. May 2017; 139(5): 052502. https://doi.org/10.1115/1.4034965
Download citation file:
Get Email Alerts
Image-based flashback detection in a hydrogen-fired gas turbine using a convolutional autoencoder
J. Eng. Gas Turbines Power
Fuel Thermal Management and Injector Part Design for LPBF Manufacturing
J. Eng. Gas Turbines Power
An investigation of a multi-injector, premix/micromix burner burning pure methane to pure hydrogen
J. Eng. Gas Turbines Power
Related Articles
Dynamic Characteristics of the Diverging Taper Honeycomb-Stator Seal
J. Turbomach (October,2006)
Theory Versus Experiment for the Rotordynamic Characteristics of a High Pressure Honeycomb Annular Gas Seal at Eccentric Positions
J. Tribol (April,2003)
Effect of Piston Ring Grooves on the Radial and Tangential Forces of a Squeeze Film Damper
J. Eng. Gas Turbines Power (January,0001)
Related Proceedings Papers
Related Chapters
CFD Simulations of a Mixed-flow Pump Using Various Turbulence Models
Mixed-flow Pumps: Modeling, Simulation, and Measurements
Experimental Characterization of a Cavitating Orifice
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Stability and Range
Design and Analysis of Centrifugal Compressors