This paper describes the design and testing of a catalytically stabilized pilot burner for current and advanced Dry Low NOx (DLN) gas turbine combustors. In this paper, application of the catalytic pilot technology to industrial engines is described using Solar Turbines’ Taurus 70 engine. The objective of the work described is to develop the catalytic pilot technology and document the emission benefits of catalytic pilot technology when compared to higher, NOx producing pilots. The catalytic pilot was designed to replace the existing pilot in the existing DLN injector without major modification to the injector. During high-pressure testing, the catalytic pilot showed no incidence of flashback or autoignition while operating over wide range of combustion temperatures. The catalytic reactor lit off at a temperature of approximately 598 K (325°C/617°F) and operated at simulated 100% and 50% load conditions without a preburner. At high pressure, the maximum catalyst surface temperature was similar to that observed during atmospheric pressure testing and considerably lower than the surface temperature expected in lean-burn catalytic devices. In single-injector rig testing, the integrated assembly of the catalytic pilot and Taurus 70 injector demonstrated NOx and CO emission less than 5 ppm @ 15% O2 for 100% and 50% load conditions along with low acoustics. The results demonstrate that a catalytic pilot burner replacing a diffusion flame or partially premixed pilot in an otherwise DLN combustor can enable operation at conditions with substantially reduced NOx emissions.

1.
Vandervort, C. L., 2000, “9 PPM NOx/CO Combustion System for “F” Class Industrial Gas Turbines,” ASME Paper No. 2000-GT-0086.
2.
Davis, L. B., and Black, S. H., 2000, “Dry Low NOx Combustion Systems for GE Heavy-Duty Gas Turbines,” General Electric Technical Report, GER-3568G, GE Power Systems, Schenectady, NY.
3.
Snyder
,
T. S.
,
Rosfjord
,
T. J.
,
Mcvey
,
J. B.
,
Hu
,
A. S.
, and
Schlein
,
B. C.
,
1996
, “
Emission and Performance of a Lean-Premixed Gas Fuel Injection System for Aeroderivative Gas Turbine Engines
,”
Trans. ASME
,
118
, pp.
38
45
.
4.
Kendrick, D. W., Bhargava, A., Colket, M. B., and Sowa, W. A., 2000, “NOx Scaling Characteristics for Industrial Gas Turbine Fuel Injectors,” ASME Paper No. 2000-GT-1998.
5.
Prade, B., Streb, H., Berenbrink, P., Schetter, B., and Pyka, G., 1996, “Development of an Improved Hybrid Burner—Initial Operating Experience in a Gas Turbine,” Proceedings from the 41st ASME IGTA Congress and Exhibition, Birmingham, UK.
6.
Pfefferle
,
W.
,
1978
, “
The Catalytic Combustor: An Approach to Cleaner Combustion
,”
J. Energy
,
2
, pp.
142
146
.
7.
Dalla Betta
,
R. A.
,
1997
, “
Catalytic Combustion Gas Turbine Systems: The Preferred Technology for Low Emissions Electric Power Production and Co-generation
,”
Catalysis Today
,
35
, pp.
129
135
.
8.
Kraemer, G., Strickland, T. R., Pfefferle, W. C., and Ritter, J., 1998, “A Compact Catalytic Combustor System for Small Turbogenerators,” Proceeding of the Joint Power Generation Conference, EC-Vol. 5, ASME New York.
9.
Fant
,
D. B.
,
Jackson
,
G. S.
,
Karim
,
H.
,
Newburry
,
D. M.
,
Dutta
,
P.
,
Smith
,
K. O.
, and
Dibble
,
R. W.
,
2000
, “
Status of Catalytic Combustion R&D for the Department of Energy Advanced Turbine Systems Program
,”
ASME J. Eng. Gas Turbines Power
,
122
, pp.
293
300
.
10.
Dalla Betta
,
R. A.
, and
Rostrup-Nielsen
,
T.
,
1999
, “
Application of Catalytic Combustion to a 1.5 MW industrial Gas Turbine
Catalysis Today
,
47
, pp.
369
375
.
11.
Sadamori, H., Tanioka, T., and Matsuhisa, T., 1994, “Development of a High Temperature Combustion Catalyst System and Prototype Catalytic Combustor Turbine Test Results,” Proc. of 1st Workshop on Catalytic Combustion, H. Arai, ed., The Research Association for Catalytic Combustion of Catalysis Society of Japan, Tokyo, pp. 18–20.
12.
Ozawa Y., Tochihara, Y., Mori, N., Yuri, I., Kanazawa, T., and Sagimori, K., 1998, “High Pressure Test Results of Catalytically Assisted Ceramic Combustor for a Gas Turbine,” ASME Paper No. 98-GT-381.
13.
Furuya
,
T.
,
Sasaki
,
K.
,
Hanakata
,
Y.
,
Mitsuya
,
K.
,
Yamada
,
M.
,
Tsuchiya
,
T.
, and
Furuse
,
Y.
,
1995
, “
Development of a Hybrid Catalytic Combustor for a 1300 Class Gas Turbine
,”
Catal. Today
,
26
, pp.
345
3501
.
14.
Rollbuhler, J. R., 1989, “Fuel-Rich Catalytic Reaction Experimental Results,” AIAA/SAE/ASME/ASEE, 27th Joint Propulsion Conference, Sacramento, CA.
15.
Brabbs, T. A., and Olson, S. L., 1985, “A Soot Free Technique for In Situ Hydrogen-Like Enrichment,” NASA Technical Paper #2498.
16.
Yee, D., Lundberg, K., and Weakley, C. K., 2000, “Field Demonstration of a 1.5 MW Industrial Gas Turbine With a Low Emission Catalytic Combustion System,” ASME Paper No. 2000-GT-088.
17.
Hoshizaki, J. A., 1997, “Operating Experience of the First Solar Taurus 70S Mechanical Drive Installation,” ASME Paper No. 97-GT-354.
18.
Smith, K., and Fahme, A., 1999, “Back Side-Cooled Combustor Liner for Lean-Premixed Combustion,” ASME Paper No. 99-GT-239.
19.
Beebe, K. W., Cutrone, M. B., Matthews, R. N., Dalla Betta, R. A., Schlatter, J. C., Furuse, Y., and Tsuchiya, T., 1995, “Design and Test of a Catalytic Combustor for a Heavy Duty Industrial Gas Turbine,” ASME Paper No. 95-GT-137.
20.
Dalla Betta, R. A., Schlatter, J. C., Nickolas, S. G., Razdan, M. K., and Smith, D. A., 1995, “Application of Catalytic Combustion Technology to Industrial Gas Turbines for Ultra-Low NOx Emissions,” ASME Paper No. 95-GT-65.
You do not currently have access to this content.