New methods to estimate both the rock strength and tooth wear while drilling with roller-bits were developed and proposed in Part 1. These methods were derived from the results of drilling tests using milled-tooth type three-cone bits with different amounts of tooth wear. In this report, these methods were extended and applied to insert type three-cone bits. The validity of the test and data analyses techniques of Part 1 were confirmed for insert bits. The methods to estimate the tooth wear proposed in Part 1 were based on the drillability strength of rock. A new approach to determine the tooth wear is presented. This new approach could be more readily applied to evaluating tooth wear when compared to the previous methods based on the drillability strength of rock.
Skip Nav Destination
e-mail: karasawa.h@aist.go.jp
Article navigation
September 2002
Technical Papers
Methods to Estimate the Rock Strength and Tooth Wear While Drilling With Roller-Bits—Part 2: Insert Bits
H. Karasawa,
e-mail: karasawa.h@aist.go.jp
H. Karasawa
National Institute of Advanced Industrial Science and Technology (AIST), 16-1 Onogawa, Tsukuba, 305-8569 Japan
Search for other works by this author on:
T. Ohno,
T. Ohno
National Institute of Advanced Industrial Science and Technology (AIST), 16-1 Onogawa, Tsukuba, 305-8569 Japan
Search for other works by this author on:
M. Kosugi,
M. Kosugi
National Institute of Advanced Industrial Science and Technology (AIST), 16-1 Onogawa, Tsukuba, 305-8569 Japan
Search for other works by this author on:
J. C. Rowley, Mem. ASME
J. C. Rowley, Mem. ASME
Pajarito Enterprises Consulting Services Inc., 3 Jemez Lane, Los Alamos, NM 87544
Search for other works by this author on:
H. Karasawa
National Institute of Advanced Industrial Science and Technology (AIST), 16-1 Onogawa, Tsukuba, 305-8569 Japan
e-mail: karasawa.h@aist.go.jp
T. Ohno
National Institute of Advanced Industrial Science and Technology (AIST), 16-1 Onogawa, Tsukuba, 305-8569 Japan
M. Kosugi
National Institute of Advanced Industrial Science and Technology (AIST), 16-1 Onogawa, Tsukuba, 305-8569 Japan
J. C. Rowley, Mem. ASME
Pajarito Enterprises Consulting Services Inc., 3 Jemez Lane, Los Alamos, NM 87544
Contributed by the Petroleum Division for publication in the JOURNAL OF ENERGY RESOURCES TECHNOLOGY. Manuscript received by the Petroleum Division, October 20, 1997; revised manuscript received April 9, 2002. Editor: A. K. Wojtanowicz.
J. Energy Resour. Technol. Sep 2002, 124(3): 133-140 (8 pages)
Published Online: August 6, 2002
Article history
Received:
October 20, 1997
Revised:
April 9, 2002
Online:
August 6, 2002
Citation
Karasawa, H., Ohno , T., Kosugi, M., and Rowley, J. C. (August 6, 2002). "Methods to Estimate the Rock Strength and Tooth Wear While Drilling With Roller-Bits—Part 2: Insert Bits ." ASME. J. Energy Resour. Technol. September 2002; 124(3): 133–140. https://doi.org/10.1115/1.1482406
Download citation file:
Get Email Alerts
Related Articles
Methods to Estimate the Rock Strength and Tooth Wear While Drilling With Roller-Bits—Part 1: Milled-Tooth Bits
J. Energy Resour. Technol (September,2002)
Proposed Practical Methods to Estimate Rock Strength and Tooth Wear While Drilling With Roller-Cone Bits
J. Energy Resour. Technol (December,2004)
Wear Characteristics of Polycrystalline Diamond Compact Drill Bits in Small Diameter Rock Drilling
J. Energy Resour. Technol (December,1985)
Ways to Improve the Drilling Effectiveness of Rock Bits by a Tribological Method
J. Tribol (April,1988)
Related Proceedings Papers
Related Chapters
A New Model for Rockburst Prediction Based on Gaussian Process
Geological Engineering: Proceedings of the 1 st International Conference (ICGE 2007)
Experimental Study and Numerical Simulation on the Compressive Strength Size Effect of Jointed Rock Mass
Proceedings of the 2010 International Conference on Mechanical, Industrial, and Manufacturing Technologies (MIMT 2010)
Theoretical Analysis and Application of Pile Shaft Resistance Strengthening Effect
International Conference on Optimization Design (ICOD 2010)