This paper investigates the use of thermoelectric (TE) devices for thermal management of downhole electronics. The research carried out will help in the mitigation of costs associated with thermal damage of downhole electronics used in oil drilling industry. An experimental set up was prepared where a TE device was used in conjunction with heat exchanger and a cold plate to remove heat from electronics module. A finned copper rod in contact with hot side of TE device was used to reject the heat out to the ambient. The experimental set up was housed inside a cylindrical vacuum flask, which was in turn placed inside an oven to simulate thermally harsh downhole conditions. Experiments were carried out with electronics heat dissipation of 0–8 W and ambient temperature of 140 °C. Due to the differences in the environmental conditions of the laboratory and the practical downhole scenario, the experiment could not completely capture the conditions of downhole heat rejection. A mathematical model of the experimental apparatus was prepared and validated against the experimental results. The model was used to predict performance of a TE device for thermal management of downhole electronics at an ambient temperature of 200–250 °C. It was observed that the ability of the thermal management system to keep electronics cool varied from 30 °C to a few degrees below the surrounding temperature, for chip wattage varying from 0 W to 8 W, respectively.
Skip Nav Destination
e-mail: ashish.sinha@gatech.edu
Article navigation
December 2011
Research Papers
Downhole Electronics Cooling Using a Thermoelectric Device and Heat Exchanger Arrangement
Ashish Sinha,
e-mail: ashish.sinha@gatech.edu
Ashish Sinha
George W Woodruff School of Mechanical Engineering, Georgia Institute of Technology
, Atlanta, GA 30332
Search for other works by this author on:
Yogendra K Joshi
Yogendra K Joshi
George W Woodruff School of Mechanical Engineering, Georgia Institute of Technology
, Atlanta, GA 30332
Search for other works by this author on:
Ashish Sinha
George W Woodruff School of Mechanical Engineering, Georgia Institute of Technology
, Atlanta, GA 30332e-mail: ashish.sinha@gatech.edu
Yogendra K Joshi
George W Woodruff School of Mechanical Engineering, Georgia Institute of Technology
, Atlanta, GA 30332J. Electron. Packag. Dec 2011, 133(4): 041005 (12 pages)
Published Online: December 9, 2011
Article history
Received:
June 15, 2010
Revised:
July 19, 2011
Online:
December 9, 2011
Published:
December 9, 2011
Citation
Sinha, A., and Joshi, Y. K. (December 9, 2011). "Downhole Electronics Cooling Using a Thermoelectric Device and Heat Exchanger Arrangement." ASME. J. Electron. Packag. December 2011; 133(4): 041005. https://doi.org/10.1115/1.4005290
Download citation file:
Get Email Alerts
Anand Model Constants of Sn–Ag–Cu Solders: What Do They Actually Mean?
J. Electron. Packag (June 2025)
Sequential Versus Concurrent Effects in Combined Stress Solder Joint Reliability
J. Electron. Packag (June 2025)
Related Articles
Heat Conduction in a Rectangular Tube With Eccentric Hot Spots
J. Thermal Sci. Eng. Appl (December,2011)
On the Development of a Low Cost Pyrheliometer
J. Sol. Energy Eng (August,2011)
The Electro-Adsorption Chiller: Performance Rating of a Novel Miniaturized Cooling Cycle for Electronics Cooling
J. Heat Transfer (September,2006)
Bejan’s Constructal Theory Analysis of Gas-Liquid Cooled Finned Modules
J. Heat Transfer (July,2011)
Related Proceedings Papers
Related Chapters
Thermoelectric Coolers
Thermal Management of Microelectronic Equipment
Engineering and Physical Modeling of Power Plant Cooling Systems
Thermal Power Plant Cooling: Context and Engineering
Thermoelectric Devices
Thermal Management of Microelectronic Equipment, Second Edition