A carbon-aerogel-supported Pt catalyst with pore size distribution and low Pt loading has been tested in a proton exchange membrane fuel cell (PEMFC). The performance of the PEMFC and kinetic parameters of the catalyst at room temperature are discussed in terms of microstructure of the support and sulfonated tetrafluoroethylene (Nafion) distribution. The PEMFCs demonstrated power densities up to at in air∕hydrogen and backpressure on both cathode and anode. Continuous cycling with upper potential sweep limits of 1.0 and leads to degradation effects that result in decreasing of the electrochemical surface area (ESA) of the catalyst. The comparison of an ESA decrease for a 1.0 and sweep limit after indicated that the higher degradation effects are due to the oxidation of carbon support.
Skip Nav Destination
e-mail: alevtina@engr.uconn.edu
Article navigation
November 2006
This article was originally published in
Journal of Fuel Cell Science and Technology
Research Papers
Aerogel-Based PEMFC Catalysts Operating at Room Temperature
A. Smirnova,
A. Smirnova
Department of Materials Science and Engineering, Connecticut Global Fuel Cell Center,
e-mail: alevtina@engr.uconn.edu
UCONN
, 44 Weaver Road, Storrs, CT 06269-5233
Search for other works by this author on:
X. Dong,
X. Dong
Aerogel Composite
, LLC c∕o ICA, Inc., 102-R Filley Street, Unit H, Bloomfield CT 06002-1853
Search for other works by this author on:
H. Hara,
H. Hara
Aerogel Composite
, LLC c∕o ICA, Inc., 102-R Filley Street, Unit H, Bloomfield CT 06002-1853
Search for other works by this author on:
N. Sammes
N. Sammes
Department of Mechanical Engineering,
UCONN
, 44 Weaver Road, Storrs, CT 06269-5233
Search for other works by this author on:
A. Smirnova
Department of Materials Science and Engineering, Connecticut Global Fuel Cell Center,
UCONN
, 44 Weaver Road, Storrs, CT 06269-5233e-mail: alevtina@engr.uconn.edu
X. Dong
Aerogel Composite
, LLC c∕o ICA, Inc., 102-R Filley Street, Unit H, Bloomfield CT 06002-1853
H. Hara
Aerogel Composite
, LLC c∕o ICA, Inc., 102-R Filley Street, Unit H, Bloomfield CT 06002-1853
N. Sammes
Department of Mechanical Engineering,
UCONN
, 44 Weaver Road, Storrs, CT 06269-5233J. Fuel Cell Sci. Technol. Nov 2006, 3(4): 477-481 (5 pages)
Published Online: May 4, 2006
Article history
Received:
December 11, 2005
Revised:
May 4, 2006
Citation
Smirnova, A., Dong, X., Hara, H., and Sammes, N. (May 4, 2006). "Aerogel-Based PEMFC Catalysts Operating at Room Temperature." ASME. J. Fuel Cell Sci. Technol. November 2006; 3(4): 477–481. https://doi.org/10.1115/1.2349532
Download citation file:
Get Email Alerts
Cited By
State of health estimation method for Lithium-ion batteries based on multi-feature fusion and BO-BiGRU model
J. Electrochem. En. Conv. Stor
A Fault Diagnosis Method for Electric Vehicle Lithium Power Batteries Based on Dual-Feature Extraction From the Time and Frequency Domains
J. Electrochem. En. Conv. Stor (August 2025)
Optimization of thermal non-uniformity challenges in liquid-cooled lithium-ion battery packs using NSGA-II
J. Electrochem. En. Conv. Stor
Ultrasound-enabled adaptive protocol for fast charging of lithium-ion batteries
J. Electrochem. En. Conv. Stor
Related Articles
Rotating Disk Electrode Study of Supported and Unsupported Catalysts for PEMFC Application
J. Fuel Cell Sci. Technol (November,2006)
Electrical Performance of PEM Fuel Cells With Different Gas Diffusion Layers
J. Fuel Cell Sci. Technol (August,2011)
Preparation and Characterization of Pt/Superfine Mesocarbon Microbead Powers Electrocatalysts
J. Fuel Cell Sci. Technol (August,2006)
A New PtRu Anode Formed by Thermal Decomposition for the Direct Method Fuel Cell
J. Fuel Cell Sci. Technol (May,2005)
Related Proceedings Papers
Related Chapters
E110opt Fuel Cladding Corrosion under PWR Conditions
Zirconium in the Nuclear Industry: 20th International Symposium
The Time-Dependent Deformation of Carbon Fiber-Reinforced Melt-Infiltrated Silicon Carbide Ceramic Matrix Composites: Stress-Rupture and Stress-Relaxation Behavior in Air at 1000°C
Mechanical, Thermal and Environmental Testing and Performance of Ceramic Composites and Components
Members in Bending
Design & Analysis of ASME Boiler and Pressure Vessel Components in the Creep Range